plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ___. ______ Type_ Serial No.__ Part No. 892256-992 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongly reco

They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. Introduction The MS2000 is a complete sanding kit that allows you to choose between 4 different sanding configurations to do a variety of tasks. Combining the versatility with the Sm

to 5 p.m. EST Mon. -- Fri. to speak with an agent. Please have the catalog number available when you call. KEY INFORMATION YOU SHOULD KNOW: • Do not operate mower unless handle is locked into position. • For best cutting results, keep blade sharpened and balanced. • Inspect and thoroughly clean your mower after each use (a deck with caked grass will degrade performance). • Make sure mowing area is clear of other persons or pets prior to starting and during operation. • Fully charge your m

To operate the system, first push button M-1 on side of switch housing, then pull the bail handle (switch lever) M-2 to the handlebar M-3. To turn the mower off, just release the bail handle. Once the bail handle has returned to the original position it will activate the "Automatic Braking Mechanism”. The motor is electrically braked and the mower blade will stop rotating in 3 seconds or less. VARIABLE SPEED SELF DRIVE SYSTEM - FIGURE N MODEL: SPCM1936 ONLY Your SPCM1936 mower is equipped wit

Refer to Operating Instructions-S witch. • Hold drill firmly to control the twisting action of the drill. If your drill is equipped with a side handle, always use the side handle. AWARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other m

To turn the too! off, release the trigger switch. The tool can be locked on for continuous operation by fully squeezing and holding the trigger switch while you depress the lock-on button shown in Fig. 3. With the lock-on button depressed, release the trigger switch and the tool will continue to run. To release from lock position, squeeze and release the trigger. Always disengage the lock before disconnecting from the power supply. VARIABLE SPEED SWITCH (JS200, JS300) BEFORE PLUGGING YOUR JIG

Slightly tighten screws alternately to position the blade, then fully tighten screws. To release, turn both screws one turn counterclockwise. (JS200, JS300) QUICK CLAMP™ BLADE CHANGE MODELS ONLY USE THIS BLADE «i TYPE BEFORE INSTALLING BLADES, TURN OFF AND UNPLUG TOOL. Your jig saw uses the Quick Clamp™ blade changing system. To install a blade, lift the Quick Clamp™ lever (Figure 2). Ensure the blade teeth are facing forward and insert the saw blade shank fully into the blade clamp. Release

(800-544-6986) Full Two-Year Home Use Warranty Black & Decker (U.S.) Inc, warrants this product for two years against any defects in material or workmanship, The defective product will be replaced or repaired at no charge in either of two ways. The first, which wii! result in exchanges only, is to return the product to the retailer from whom it was-purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for excha

To release from lock position, squeeze and release the trigger switch once. Always disengage the the lock before disconnecting from the power supply. BEVEL ADJUSTMENT (FIGURES 3 &4J TURN OFF AND UNPLUG TOOL The shoe (5) can be angled up to 45° on either side. To do this, disconnect your jig saw from the power supply. Raise the dust shroud (3) and loosen both screws on the shoe plate with a screwdriver. Pull the shoe plate backward a little, and set the desired angular adjustment according to t

You will develop your own techniques which will make the job easier and faster as you learn power polishing. As mentioned previously you should use utmost care when power polishing around or over sharp objects and contours of the car body. It is very important to use the correct pressure while polishing various sections of an automobile body. For example, light pressure should be applied when polishing over sharp edges of body panels, or over edges of the rain gutter along the top. Since every