A and B). 2. Disassemble the antenna mounting hardware and cable from the Antenna Assembly noting how it was assembled. (See Fig. C). 3. Select the mounting location using the following considerations: (See Fig. D) A. The antenna cable is 40” long. Verify the selected antenna location will reach the radio’s antenna socket. B. Check behind the area for access for mounting and clearance for cable/base assembly. C. The mounting location (if at all possible) should be metal for best grounding o

LIGHT SWITCH 3. CHARGING INDICATOR 4. LCD DISPLAY with BACK LIGHT 5. RADIO POWER INDICATOR MODEL MR-720 6. SIREN ON-OFF SWITCH 7. POWER SOURCE SWITCH 8. DYNAMO CRANK HANDLE 9. TUNING KNOB SELF- POWERED AM/ FM WEATHER BAND CLOCK RADIO 10. VOLUME KNOB 11. LAMP HEAD 12. SPEAKER 13. 360° TELESCOPIC ANTENNA 14. BACK LIGHT BUTTON 15. MINIUTE SET BUTTON 16. HOUR SET BUTTON 17. ALARM ON- OFF BUTTON 18. TIME SET BUTTON 19. ALARM SET BUTTON 20. SWAP RADIO/CLOCK DISPLAY BUTTON 21. PRESET WHEATHER CHANNEL S

The FM antenna is built in tothiscord.lt must be fully extended to provide the best FM reception. SURE-ALARM BATTERY BACK UP SYSTEM The Sure-Alarm battery back up system in this clock radio will maintain the time and alarm settings in the event of a temporary power interruption. When the AC power is restored the time and alarm settings will be correct. If the AC power is off at your wake up time, the Sure-Alarm system will use the battery power to turn on the radio or buzzer alarm as usual, as

Release the ALARM button to return to current time. Icon “AL” disappeared. WAKE TO RADIO 1. Set the FUNCTION Selector to “RADIO” and Power on the unit. 2. Select the band, station, and volume level that you wish to hear when the alarm comes 'On'. S 3. Set the FUNCTION Selector to “AUTO”. The ALARM Indicator will light up. 4. Reconfirm the wake up time settings by pressing the ALARM button. 5. The radio will turn 'On' at the selected wake up time. Icon “Z z” will blink while the alarm sounds. 6.

To turn ON : Press PLAY/PAUSE button (playback starts) To turn OFF : Press STOP button once for standby mode. Press STOP button again to turn off the power. To Remove the Disc 1. Slide the LOCK switch (5) to its original position. 2. Press the CD LID OPEN button to open the CD compartment lid. 3. Hold the edge and gently press the center pivot as illustrated, then pick up the disc. CAUTION: WAIT FOR THE DISC TO STOP SPINNING BEFORE SLIDING THE OPEN SWITCH AND OPENING THE LID. Notes on CD-R/RW Di

CAUTION • AVOID EXCESSIVE VOLUME LEVELS FOR LONG PERIODS OF TIME WHEN USING THE HEADPHONES. PROLONGED USE AT HIGH LEVELS MAY IMPAIR YOUR HEARING. • Do not use earphones while operating a motorized vehicle, as it may create a traffic hazard and is illegal in many areas. BASIC OPERATION NOTE: This unit can also play 3 inch (8cm) single CDs without an adaptor. Do not use a CD single adaptor for these smaller discs. 1. Press the CD LID OPEN button to release the CD lid. 2. Insert a disc with the lab

NOTE: Check your vehicle's owners manual before disconnecting the battery. Disconnecting the battery in some vehicles may require an anti-theft code when reconnecting for stereo operation. Some vehicles may run rough after reconnecting the battery and require service to have the on-board computer reset. Check with your local dealer if you are uncertain. 2. Run suitable AWG wire to where the amplifier will be mounted (run 1 foot extra than you think you will need). Use rubber grommets where wires

We've tried to make the instructions in this book clear and easy to follow. For your Jensen amplifier to work right, it must be installed correctly. This manual will show you how to install your new amplifier like a pro. It's a good idea to read all of these instructions before you begin the installation. Most installations are straightforward and can be handled by a do-it-yourselfer with the right tools, patience, and the ability to follow instructions. But, do-it-yourself installation isn't fo

1. Wake to Alarm - Repeatedly press ALM.1 / MEM-or ALM.2 / MEM+ Button to enter ALARM mode. “ ” or “ ” will appear in the display. Two different rings for Alarm 1 and Alarm 2 will sound when the alarm time is reached. 2. Wake to Radio - Repeatedly press ALM.1 /MEM-or ALM.2 / MEM+ Button to enter the RADIO mode, “ ” or “ ” will appear in the display. - Follow the procedure in “TUNER OPERATION” to select your desired radio station. - Press the POWER/STANDBY Button to turn off the unit. The radio w