Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
1. Wake to Alarm - Repeatedly press ALM.1 / MEM-or ALM.2 / MEM+ Button to enter ALARM mode. “ ” or “ ” will appear in the display. Two different rings for Alarm 1 and Alarm 2 will sound when the alarm time is reached. 2. Wake to Radio - Repeatedly press ALM.1 /MEM-or ALM.2 / MEM+ Button to enter the RADIO mode, “ ” or “ ” will appear in the display. - Follow the procedure in “TUNER OPERATION” to select your desired radio station. - Press the POWER/STANDBY Button to turn off the unit. The radio will automatically turn on when the alarm time is reached. 3. Wake to iPod - Briefly press ALM.1 / MEM-or ALM.2 / MEM+ Button to select iPod mode, “ ” or “ ” will appear in the display. - Follow the procedure in “DOCKING YOUR iPOD” to play your iPod. - Press POWER/STANDBY Button to turn the unit off. When the alarm time is reached, the iPod will automatically start playing. Note: i. After waking to iPod or Radio alarm, the volume level of the iPod or radio can be adjusted as needed. ii. After the alarm is on, the LCD backlight will automatically be set to high. 4. Light - The light located on the top of the JiMS-182 works with all “Wake to” settings. The light will begin to light one minute before the alarm time is reached and will increase to full brightness by the time the alarm time is reached. 9 Stopping the Alarm The alarm is programmed to continuously sound for 60 minutes. To stop the alarm, follow the directions below. 1. SNOOZE / DIMMER Button – Press this button to stop the alarm temporarily. The alarm will stop and automatically resume after 9 minutes. 2. POWER/STANDBY Button – Press this Button to stop the alarm which will sound again 24 hours later. 3. ALM.1 / MEM-or ALM.2 / MEM+ Button – Press this Button once to stop the alarm and the alarm will sound again 24 hours later. DIMMER Operation (With AC Adaptor plugged in) In power off mode, press the SNOOZE / DIMMER Button repeatedly to adjust the LCD backlight to low, middle or high as desired. Note: i. With the AC Adaptor plugged in and with power off, press any button except SNOOZE/DIMMER and the LCD backlight will automatically set to high and resume to the preset brightness in approximately 5 seconds. ii. If using battery power, the LCD backlit is always set to the dimmest level in order to conserve battery power. Press any button the LCD backlight will automatically set to high and resume to the dimmest level in approximately 5 seconds. Turning the Lamp On/Off 1. You can press the LIGHT button to turn the Lamp on and off. 2. The Lamp will also light automatically one minute before the alarm time is reached and increase to the full brightest level when the alarm time is reached. 3. When you stop the alarm by pressing the SNOOZE/DIMMER, POWER, ALM.1/MEM-or ALM.2/MEM+ Button, the Lamp will be turned off at the same time. You can also press the LIGHT Button to turn off the Lamp directly. 4. If the Lamp is on before waking to alarm, radio or iPod, when you stop the alarm by pressing the SNOOZE/DIMMER, POWER/STANDBY, ALM.1/MEMor ALM.2/MEM+ Buttons, the Lamp will remain on. To turn the Lamp off press the LIGHT Button once. SLEEP OPERATION Your JiMS-182 can be programmed to turn off according to your preset sleep time. The sleep time can be set for 15, 30, 60, 90 or 120 minutes. 10 Turn on the JiMS-182 on and select either iPod, Radio or AUX function. 1. Press the SLEEP Button repeatedly until the desired sleep time is shown on the Display. For example, if it is 10:00 PM and you set the sleep time for 30 minutes, the display will show: Preset Sleep Time Current time 2. The JiMS-182 will play and turn off automatically after the 30 minute Sleep time expires at 10:30 PM. If you want to cancel the sleep time before the time expires, press POWER/STANDBY Button once. 3. The Light can also be used during the Sleep mode. Press the LIGHT Button once to turn on the Light. The light will dim and go off when the preset sleep time expires. Note: In AUX Mode, if the playing time of the external device is shorter than your selected sleep time, the music will stop when the external device shuts off. CARE AND MAINTENANCE 1. Clean the unit with a damp (never wet) cloth. Solvent or detergent should never be used. 2. Avoid leaving your unit in direct sunlight or in hot, humid or dusty places. 3. Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps or motors. 4. For better Clock Display clarity, avoid operating the unit under direct sunlight or in strong room illumination. TROUBLESHOOTING GUIDE Should the system exhibit a problem, please check the following before seeking service. 11 Symptom Possible Cause Solution Radio Noise or sound distorted on AM or FM broadcasting. Station is not tuned properly for AM or FM. Fine-tune the AM or FM broadcast station. FM: The broadcast station signal is weak Find another station or relocate the unit until the best reception is obtained. AM: The location of the built-in antenna is not correct. R...