Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
The FM antenna is built in tothiscord.lt must be fully extended to provide the best FM reception. SURE-ALARM BATTERY BACK UP SYSTEM The Sure-Alarm battery back up system in this clock radio will maintain the time and alarm settings in the event of a temporary power interruption. When the AC power is restored the time and alarm settings will be correct. If the AC power is off at your wake up time, the Sure-Alarm system will use the battery power to turn on the radio or buzzer alarm as usual, as long as the back up battery is installed and has sufficient power remaining. The Sure-Alarm battery back up system requires one 9-volt battery, not included. We recommend that you install an alkaline battery for longest life and best performance. 4 To instal I the battery Open the battery compartment cover on the bottom of the radio by pressi ng the tab in the direction of the arrow. Dr I • Connect the 9-volt battery to the battery clip. It can only be connected oneway. Push the battery into the battery compartment and replace the cover. POWER FAILURE INDICATOR If no battery is installed in the radio, or if the battery in the compartment is weak or dead, the time and alarm settings will be lost if the power is interrupted. When the ACpower is restored theclock display will begin flashing. This indicates that the time display is incorrect and needs to be reset. IMPORTANT: After you reset the time, be sure to reset your alarm settings as well. 5 LOCATION OF CONTROLSAND INDICATORS 12 13 1. ALARMSelectorSwitch. (BUZZER/AUTO/ON/OFF) 2. TIME Button. 3. BAND(AM/FM)SelectorSwitch. 4. MIN.(Minute) Button. 5. HOURButton. 6. Speaker.(Atrearcabinet) 7. VOLUME Control. 8. SNOOZE Button. 9. TUNING Control. 10. SLEEP Button. 11. ALARM Button. 12. PM Indicator. 13. ALM (Alarm) 'On' Indicator. 14. Time LED Display. 15. AC Power Cord. 16. Battery Compartment. (At bottom of cabinet) 6 OPERATING INSTRUCTIONS SETTING THE CLOCK When you connect the radio to your AC outlet for the first time, the clock display will begin flashing "12:00". The flashing will stop when you set the time. 1. Depress the TIME button and the HOUR button to set the correct Hour. 2. Depress the TIME button and the MIN button to set the correct Minute. r PM indicator--• ALM indicator--• NOTE : Be sure to observe the PM indicator to make sure that the time is set correctly for AM or PM. If the PM indicator is 'On1, the time displayed is "PM". If the PM indicator is'Off', the time display is "AM". SETTING THE WAKE UP TIMES 1. Depress the ALARM button and the HOUR button to set the correct wake up Hour. 2. Depress the ALARM button and the MIN button to set the correct wake up Minute. NOTE : Be sure that you have set the wake up time correctly by observing the PM indicator. If the PM indicator is'On1, the wake up time is "PM". If the PM indicator is 'Off', the wake up time is "AM". CHECKING THE WAKE UP TIMES Whenever you want to check the wake up time, simply press ALARM button. The display will change from the correct time to the wake up time. Release the ALARM button to return to the correct time. IJ • nn 1C • uu 7 LISTENING TO THE RADIO 1. Set the BAND selector to the desired band, AM or FM. 2. Set the VOLUME control to a low setting. 3. Slide the ALARM switch to the ON position. 4. Select your desired station with the TUNING control. 5. Adjust the VOLUME control to a desired setting. 6. When you finished listening, slide the ALARM selector to the OFF position to turn the radio 'Off1. ANTENNA INFORMATION AM-The AM barantenna is insidethecabinet.lfthe AMreception is weak, change theposition of the cabinetuntilthe internal antenna picks up the strongest signal FM - The FM antenna is built-in to the AC power cord. If the FM reception is weak try varying the position and direction of the powercorduntil you find the strongest signal. WAKETO RADIO 1. Slide the ALARM selector to the ON position and select the band, station, and volume level that you wish to hear when the alarm comes 'On'.then slide the ALARM selector to the AUTO position and the ALM indicator will light up. 2. Reconfirm the wake up time settings by pressing the ALARM button. 3. The radio will turn'On'at the selected wakeuptime.lt will play for about two hours and then shut offautomatically. 4. To stop the radio sooner, press the ALARM button. The radio will stop but thealarm remainsset and willturntheradioon again atthesametimeon the following day. 5. If youdonot want thealarm toturn the radioononthe following day, set the ALARM selector to the 'OFF' position. 8 WAKE TO BUZZER 1. Set the ALARM selector to the BUZZER position. The ALM indicator will light up to confirm that the alarm is set. 2. The buzzer will sound at the selected wake up time.lt will continue for about two hours and then shut off automatically. 3. To stop the buzzer sooner, press the ALARM button. The buzzer willstopbut the alarm remains set and will turn the buzzer...