Use a nylon brush on badly soiled items. • Wipe dry after cleaning and replace items. SOLID PLATES Before using the plates for the first time, switch them on for four minutes at the highest setting. This allows the factory applied protective coating to burn in. The markings around the plate control knobs represent the following heat settings: Position 1 = Warming. 2 = Slow simmer. 3 = Simmer. 4 = Medium heat. 5 = High heat 6 = Boiling and frying. The plate indicator light will glow when a plate

in all poles. • The appliance must be connected by means of wires having an appropriate temperature marking. • A disconnection (terminal block) must be provided in the fixed wiring. • It is essential that a licensed electrician connects the stove to the electricity supply point in the kitchen. • The rated current is printed on the serial sticker located on the rear panel of the stove. IMPORTANT: This appliance must be earthed and the manufacturer and the seller do not accept responsibility for a

15A. Earthed wall socket. SELECTOR KNOB • The stove is a plug-in model with a 15A. Power supply. • It is therefore not possible to use all the elements at the same time. • Set the selector to the required position. OVEN CONTROL (BAKING) • Set the selector to bake. • Set the oven control to the desired temperature. • The indicator light will glow and remain on until the oven has reached the selected temperature. • When the indicator light switches off, the food should be placed in the ov

The advantages are: 1. Both trays may be used at the same time. 2. Different dishes can be cooked simultaneously without flavour or aroma transfer. Hence fish, meat and cakes can be baked at the same time. 3. The oven door may be opened any time for inspection purposes without risking a flop. 4. By circulating hot air around the food, spit-roast chickens may be done without using a rotisserie. Cooking • Ensure that the timer is set to manual. • Set the multifunction selector to Thermofan oven an

We trust that you will enjoy many years of trouble free use. Please read these instructions carefully before using the stove. This manual will provide you with information on how to operate and care for your product in order that you gain the maximum benefit from it. UNPACKING • Please ensure that packaging material is disposed of in a responsible manner. • Plastic bags should be cut up to prevent children playing with them and accidentally suffocating. • Remove all packing from the oven cavity

holes through the top holes in the bottom chimney and through the lower end of the top chimney duct. • Fasten the two chimneys to the centre chimney bracket. Top chimney duct Drill two 3.5mm Diameter holes and secure two chimney ducts to mounting bracket. Mounting bracket Bottom chimney duct Page 5 Grease filters. Grease filters. • Remove the plastic outer protective lining on the grease filters before fitting them to the extractor hood. • To fit the filters, engage the two lugs at the rear of e

• Damage through improper use or installation. Problem check. Before calling a service technician to assist with a problem please check: • The main distribution board. See if a circuit breaker has tripped or a fuse has blown. • The wall socket. • Have the filters been cleaned? • Is the chimney blocked? Remember that you may be charged for a service call even during the warranty period if the fault is due to or caused by any of the above. Service. • If you have followed the instructions and still

ceiling ceiling ceiling Page 3 Installation.. Installation.. Installation sequence; 1. Extractor unit / chimney brackets. 2. Top chimney duct 3. Bottom chimney duct • Carefully remove the extractor hood and the components from the packaging. • Remove the grease filters. CEILING MOUNTING TEMPLATE CEILING MOUNTING BRACKET POSITION CUT TEMPLATE TOP OF CEILING HOOD TEMPLATE LINE FROM CENTRE OF STOVE TO CEILING HORIZONTAL LINE 750 • Draw a fine vertical line on the wall from the rear-centre of the ho

Electrical connection. • The extractor hood uses a 220250V/ 50Hz power supply. • If the mains power cord is damaged, it must be replaced by a qualified electrician. • The power cord is located in the chimney area. Should you require an installation with no visible wiring, a 15 amp earthed plug socket should be accessible either in the ceiling above the extractor hood or on the wall behind the chimney area. (A qualified electrician should provide this facility). • The extractor hood must be earth