Login:

RIDGID OL50135AL

heruntergeladen wurde: 18Dateigröße: 10 mb    Hersteller: RIDGID  
Kategorie: Pumps

Your tool is wired at the factory for operation using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15amp branch circuit. Use a 15amp time delay type fuse or circuit breaker. To reduce the risk of shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately. The A-C motor used on this compressor is a PSC, permanent split capacitor type, having the following specification. It is wired at the factory for operation on 110V-120

RIDGID IN625301AV

heruntergeladen wurde: 12Dateigröße: 5 mb    Hersteller: RIDGID  
Kategorie: Pumps

head cap screw 4 12 33478 WL008400AV Fan * 1 13 17943 ST072224AV 3/8 inch Compression Elbow 1 14 -WL015304SJ Belt kit (Includes #10, 12, check valve, & ferrules) * 1 REPAIR PARTS KITS s l -- WL211201SJ WL211100AJ Valve plate kit (Includes #2-7) Head bolt kit (Set of 4 ea., part #11) 1 1 † = Standard Hardware Item --= Not Available * = Considered wear items 17 catalog no. OF25150A Model no. OF25150A serial no. _____________ _ The model and serial numbers may be found on your unit. You should reco

RIDGID OF25150A

heruntergeladen wurde: 10Dateigröße: 5 mb    Hersteller: RIDGID  
Kategorie: Pumps

Air pressure is measured in pounds per square inch (PSI). Most tools have maximum pressure ratings. Never exceed the maximum pressure rating of the tool you are using. Be sure this gauge reads ZERO before changing air tools or disconnecting hose from outlet. 3 Handle Used to move the compressor. 4 Regulator Knob This knob controls air pressure to an air operated tool or paint spray gun. Turning the knob clockwise increases air pressure at the outlet. Turning counterclockwise will lower air press

RIDGID RIGID OF25135A

heruntergeladen wurde: 11Dateigröße: 4 mb    Hersteller: RIDGID  
Kategorie: Pumps

20. Spray in a well ventilated area, to keep fumes from collecting and causing health and fire hazards. 21. Do not spray in vicinity of open flames or other places where a spark can cause ignition. Do not smoke when spraying paint, insecticides, or other flammable substances. 22. Use a respirator when spraying. 23. NEVER reset safety valve or pressure switch. Keep safety valve free from paint and other accumulations. This provides safety against over pressure. 24. Do regular maintenance; keep al

RIDGID R848

heruntergeladen wurde: 7Dateigröße: 4 mb    Hersteller: RIDGID  
Kategorie: Jack Planes

n Apply downward pressure toward the rear handle as you reach the end of the planed cut. This helps keep the rear section of the planer base in contact with the work and prevents the front of the planer from gouging the cut. WARNING: Be careful to avoid hitting nails or any other foreign objects during planing operation; this action could nick, crack, or damage blades. NOTE: We suggest that you always keep an extra set of blades on hand. As soon as the blades in your planer show signs of becomin

RIDGID R888

heruntergeladen wurde: 22Dateigröße: 4 mb    Hersteller: RIDGID  
Kategorie: Jack Planes

ATTACHING THE PLANER TO A VACUUM See Figure 3. The chip collection system of the hand planer has a 1-1/4 in. port for inserting a vacuum hose. . Remove the dust bag. . Attach a vacuum hose to the chip exhaust. . Connect the vacuum to a power supply. WARNING: When the tool is not connected to a vacuum, always reinstall the dust bag back onto the tool. Failure to do so could cause dust or foreign objects to be thrown into your face or eyes, which could result in possible serious injury. 11 WARNING

RIDGID R250AFA

heruntergeladen wurde: 0Dateigröße: 3 mb    Hersteller: RIDGID  
Kategorie: Nailers

GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. LUBRICATION ..Frequent,

RIDGID OF45150B

heruntergeladen wurde: 11Dateigröße: 3 mb    Hersteller: RIDGID  
Kategorie: Pumps

Turning counterclockwise will lower air pressure at the outlet. Fully counterclockwise will shut off the flow of air completely. Close Open 5. Tank Pressure Gauge. Gauge shows pressure in air receiver indicating compressor is building pressure properly. 6. ASME Safety Valve. This valve automatically releases air if the tank pressure exceeds the preset maximum. 7. Air Outlet Fittings. These fittings are 1/4” universal-style quick connect fittings and allow rapid tool changes. 8. Air Filter. The a

RIDGID R175RND

heruntergeladen wurde: 2Dateigröße: 3 mb    Hersteller: RIDGID  
Kategorie: Nailers

. Rotate the selector to Position A. . Release the trigger lever pivot pin. WARNING: The nailer will not function properly if the selector is not securely seated in either Position A or B. Always assure the selector is seated properly to avoid an unexpected fastener discharge and possible serious personal injury. . Reconnect the tool to the air supply. . Grip the tool firmly to maintain control. Position the nose of the tool onto the work surface. . Push the tool against the work surface to depr

RIDGID R175RNA

heruntergeladen wurde: 4Dateigröße: 3 mb    Hersteller: RIDGID  
Kategorie: Nailers

Position 3 1-1/2 in., 1-3/4 in. SPOOL Fig. 5 Fig. 6 POSITION 1 POSITION 2 POSITION 3 SPOOL NAIL TRAY 14 LOADING THE TOOL WITH NAILS See Figures 7 - 9. WARNING: The tool’s driving mechanism may cycle when the tool is first connected to the air supply. Always connect the tool to the air supply before loading nails to prevent injury from unintended cycling. Always make sure the tool’s magazine is empty at the beginning of each work session, before connecting to an air supply. WARNING: Keep the tool





Kategorien