Manua. PNEG-37. Fan and Heate. TABLE OF CONTENT. Roof Warning, Operation & Safety ................................................................................. . Safety Alert Decals ..................................................................................................... . 2000 Vane Axial Fans ................................................................................................... . 2000 Centrifugal Fan Service Guide ....................................................

The diagram details the correct main power installation for 220V 1 ph, 230V ph, 460V 3ph, 575V 3ph, and 380V 50hz power supplies. On all three phase systems put the leg with the highest potential difference between that leg and ground ( wild or high voltage leg) on the center terminal (L2) at the motor starter. NOTE: Standard electrical safety should be used. (Refer to the National Electrical Code Standard Handbook by the National Fire Protection Association). A qualified electrician should make

PNEG-67. Series 200. Autoflo. Fan/Heate. Control Installatio. Instruction. MODEL # 2TF - __ __ - __ __ _. MODEL # 2TFC- __ __ __ __ _. MODEL # 2TAF - __ __ __ _. This equipment shall be installed in accordance iwth the current INSTALLATION CODES FOR GAS BURNING APPLICANCES AND EQUIPMENT, CAN1_B149.1 and B149.2, or applicable provincial regulations which should be carefully followed in all cases. Authorities having jurisdiction shuld be consulted before installations are made. 2000 Autoflo. TABLE

2) If the bin is 2.66” corrugation the hole should be centered on an outside hill. 3) If the bin is 4.00” corrugation the hole should be centered on an outside valley. 4) Use the mounting plate as a pattern and drill four 3/8” holes through the sidewall at the swich location so the place can be bolted to the bin. 5) Add foam weather strip around the top and side of the mounting plate. 6) Caulk the underside of the mounting plate, on all sides of the 2” hole, and where the plate meets the bin. 7)

8 EMCS Portable Dryer (1993-1998) Safety Voltage Check Points ................................................................................................................................. 9 Programming Instructions for EMCS Grain Dryers .............................................................................................. 10 EMCS Display Board ............................................................................................................................................ 1

2 and 3 Module Network Portable Dryer Models Operators Manual PNEG-951 Date: 2-22-2006 PNEG-951 Table of Contents Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7 Section 8 Warranty.............................................................................7 Safety First........................................................................9 Safety Alert Symbol...........................................................................................10 Safety Alert Decals.

1 2 1a 4a 5 3 355 3 354 Right side Left side Frame **NOTE: The parts pointed out on this page are listed on page 7. PNEG-1447 The fan heater end of the dryer is considered by GSI as the front end of the dryer ( theforeground of this photograph is the front end. Right and left sides are labeled above) . Frame Right

5 Dryer Operation .................................................................................................................................. 6 Emergency Stop ................................................................................................................................. 6 Safety Precautions ............................................................................................................................. 7 Chapter 2 Safety Alert Decals .........................

3. 4. 5. 6. 7. 8. 9. All wire connections Spark plug gap .125 Pipetrain tightness and gas leaks Flame sensor tight Fuse in place, extra fuse provided Time delay reset Indicator light Pressure gauge Regulator adjusted 10. Shut off valve operates correctly 11. Vapor high limit 12. Unit cycles on to off 13. Heat rise even across transition 14. Unit cycles hi to lo (hi-lo only) 15. Mod valve holds temperature within 1 degree (mod units only). 16. All decals and serial number tag 17. Aesthetic appear

Watch plenum temperature as burner goes through a few cycles, to be sure that it is operating properly. 1. Hi-limit and cycling thermostat must be wired into heater control box for heater to operate. 2. Open all manual shutoff valves to heater unit. 3. Start fan. This will supply power to heater. 4. Turn thermostat dial to its highest setting. 5. Turn toggle switch on. Both red lights should light up indicating power to the control circuit. 6. Heater should now be lit. If not check to see that a