Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Black & Decker Dateigröße: 8.66 mb Dateiname: Unterrichtssprache:

To release from lock position, squeeze and release the trigger switch once. Always disengage the the lock before disconnecting from the power supply. BEVEL ADJUSTMENT (FIGURES 3 &4J TURN OFF AND UNPLUG TOOL The shoe (5) can be angled up to 45° on either side. To do this, disconnect your jig saw from the power supply. Raise the dust shroud (3) and loosen both screws on the shoe plate with a screwdriver. Pull the shoe plate backward a little, and set the desired angular adjustment according to the scale or push the shoe plate forward for fixed locks at 0°,15°,30°,or 45°. Tighten the screws to secure. Although the scale and notches are accurate for most purposes it is advisable for very accurate angle cutting to use a protractor to set the shoe. Make a test cut on some scrap material to check the accuracy of the angle. To reset the shoe for a square cut, loosen the clamp screws and move the shoe until it is approximately 90° to the blade, and then, while applying slight forward pressure on the shoe, retighten the clamp screws. HANDY HINTS CUTTING LAMINATES The blades of your jig saw cut on the upstroke so any tendency for edge splintering will occur on the face of the material nearest the saw shoe. When sawing thin wood or plastic laminates use a fine tooth metal cutting blade and cut from the back surface of the material. To minimize the risk of chipping the edges of plastic laminate, clamp a piece of scrap wood or hardboard to both sides of the laminate to form a sandwich, and saw through the complete assembly Always select the right blade for the job. POCKET CUTTING The saw blade can be inserted directly.into a wood surface without first drilling a pilot hole, thus eliminating a drilling operation. First measure and clearly mark the surface to be cut. Then tip your jig saw forward so that the rounded tips of the shoe rest on the work surface but with the blade well clear of it. Switch your jigsaw on and move the saw down until the moving blade is exactly over the chosen point of entry. Lower the rear of the shoe down towards the work slowly, maintaining a firm pivoting pressure on the shoe tips with the blade exactly on the required line. Do not move your jig saw forward along the cut line until the saw blade has completely entered the material and the shoe comes to rest flat on its surface. CUTTING METAL Your jig saw can be used for cutting light gauge ferrous sheet and non-ferrous metals such as copper, brass, aluminum, etc. It is advisable when cutting thin sheet to clamp a backing sheet of soft wood or plywood to the work as this will enable you to obtain a clean cut without vibration and the possibility of tearing the metal. Both metal and wood backing are sawn together. Do not force the cutting blade into the metal as this will reduce the life of the blade and possibly damage the motor. Cutting thin metal will take longer than cutting even a relatively thick piece of wood, so do not be tempted to speed up the operation by forcing the saw. Spread a thin film of oil along the proposed cutting line before commencing to saw metal. Always select the right blade for the job. AWARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using tool. Maintenance Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. Lubrication Black & Decker tools are properly lubricated at the factory and are ready for use. Accessories Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1 -800-54-HOW-TO. (800-544-6986) A CAUTION: The use of any accessory or attachment not recommended may be hazardous. Service Information The nickel-cadmium rechargeable batteries used in the screwdriver will last through many discharge cycles. When they eventually wear out, Black and Decker will replace them at a reasonable charge. We offer a full network of company-owned and authorized service locations throughout North America. AH Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-8QO-54-HOW TO. (800-544-6986) Full Two-Year Home Use Warranty Black & Decker (U.S.) Inc, warrants this product for two years against any defects in material or workmanship, The defect...

Herunterladen

Geben Sie zwei Ziffern: