Save these instructions for future reference. Only use this appliance as an exhaust ventilation system for the removal of cooking vapors. DO NOT use to expel flammable substances or any other materials or vapors. The installation procedures in this manual are intended for qualified installers, service technicians or persons with similar qualified background. DO NOT attempt to install this appliance yourself. Ensure that electrical power is turned off at source before commencing installation. All

Please read all the instructions in this manual before installing the appliance. Save these instructions for future reference. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure they do not play with the appliance. If the range hood is vented, the air so vented must be ducted into a dedicated duct that is not showed with any other equipment whatsoever. All ducting must conform to all requirements of the loc

Position the upper chimney so that it can be fixed via the holes on the side of the ‘Y” bracket on the ceiling (refer to Figure 11). Connecting the Screen (SU 202 Only) Before attaching the screen the power unit wipe the face of the flange to ensure there is no Figure 11 5 Figure 12 Figure 13 grit present – if there is this will most definitely crack the glass. The plastic washers must be positioned between the screw head and the glass. Fit the screen – please have someone hold this in place whi

To install this appliance in these countries, it is essential to obtain the translated instructions and in some cases the appliance will require modification. Contact Stovax for further information. s IMPORTANT For use with 230v 50 - 60Hz electricity supply only. Please read these instructions carefully and in conjunction with the appropriate Riva Installation and User instructions. Care must be taken when handling the stove to avoid injury or damage to the stove. They will be neede

Attach bracket “A” to the ceiling permanently. If re-circulating, attach the deflector to Bracket “A” before fixing it to the ceiling – refer schematic on page 5. Fix Bracket “C” to the power unit with the nuts and washers supplied (Items “A” on the schematic on page 5). Please ensure that the bracket is installed as shown to enable full access to the square plastic black box and the metal electrical junction box. Slide Bracket “B” over Bracket “C” (once again ensure full access to the plastic a

Ensure the entire structure is sturdy -serious injury, death and MAJOR damage could result should the unit not be well connected to the frame structure within the ceiling. This is of utmost importance – do not go any further until this has been tested and double checked – the installer has sole responsibility for the safe installation of this product. Connecting Electricity and Ducting Make sure power is turned off at the source. Make the electrical connection (see figure 1). Test the functionin

When frying, oil in the pan can easily overheat and ignite. Heat oil slowly in an appropriately sized pot (covering the entire burner) to reduce the risk of boiling over and burning In the event of a range top grease fire, observe the following: Switch OFF the range hood. Turn off the cook top then smother flames with a close fitting lid, cookie sheet or other metal tray. If the flames do not go out immediately. EVACUATE AND CALL THE FIRE DEPARTMENT. Never pick up a flaming pan – you may be burn

By following this test assembly you will be able to finalize the correct length of the assembly before mounting it to the ceiling. Test assembly should include actually attaching the following items together – refer schematic of components and “Fixing the main support brackets” below – Brackets A, B, C, power unit and deflector if re-circulating. This is also a good time to test the electrical functioning of the hood before it is installed. Before switching on the light or lights, ensure the tap

Follow the instructions for cleaning filters in this booklet. Once the grease filters have been cleaned and replaced, reset by pressing the timer button (F). Do not rely solely on this indicator. Generally, the grease filter should be washed on a regular basis to avoid grease filter fires. The blower should be turned on for approximately 5 minutes before cooking in order to establish air currents upward through the hood. Use the low speeds for normal use and the higher speeds for strong odors an

Do not switch on the lights with the hood flat on any surface as the intense heat will burn the surface and destroy the lamps. Connect a power supply to the unit and test all functions. Installation of the island hood consists of fixing the ceiling bracket to substantial members in the ceiling. The bracket must be fixed to the frame by screwing through the ceiling into the heavy members inside the ceiling. This is critically important as the entire hood fan hangs from this position, and ceiling