Hold it to skip forwards. B. During RADIO mode, press and hold or for more than 2 seconds you can manual search channel. Then press ►Hor ,you can have auto search channel. 5.APS BUTTON IN RADIO MODE: When short pressing, the radio searches for each preset station. When the field strength level is more than the threshold level of stop level, the radio is holding at that preset number for few secretary with releasing mute, and than searches again. In FM band, FM 1, FM 2 and FM 3 is checked on

POWER SWITCH: Press to switch amplifier on. 2. FM ANTENNA BOOSTER SWITCH: Press the switch to improve FM reception. The switch works independently even when power switch off. 3. HOLD SWITCH: Press the switch to light up all the LED indicator built in the shaft of slide equalizer control. (Scan/Level switch at "SCAN" position). 4. SCAN/LEVEL SWITCH: When switch set at "SCAN" position, the LEOs built in each slide control scan automatically from left to right over each frequency points. (Hold swit

Turn to off for no effect. 10) Power LED: Illuminates when power is switched on. 11) Master: Adjusts overall volume. 1) Power Switch: Switches amplifier on/off. 2) Voltage Selector: AC 110/220 Volt Selectable Switch. 3) Power Cord: Connect the included power cord here. Plug in to a grounded power outlet only! 4) Phones: This is your headphone connection. Inserting the headphones disables the internal speaker(great for practicing). A 5) Line Out: Lets you output a line level signal (no

Bridging the outputs will damage your amplifier! 11 2 ch amp PB440X•4champ PB442X mounting and installation Please read the Installation Precautions section below before installing your Pyramid Super Blue amplifier, and then refer to the diagrams provided to connect power, audio input and speaker connections according to your own system configuration requirements. Installation Precautions • Before you drill or cut any holes, investigate your car’s layout very carefully. Take care when you work n

Super Blue amps are some of the most advanced car amplification products available. These quality audio products are designed and engineered to afford you years of uncompromised musical service. Pyramid has utilized the latest electronic technologies in order to deliver a superb listening experience. The Super Blue line has been designed to ensure adequate headroom for even the most demanding peaks and dynamic ranges found on today’s CD’s and recordings. Used properly, these amplifiers will prov

2 WIRNG DIAGRAM 3 CONTROL LOCATIONS 4 GETTING STARTED 5~7 MP3 PLAYER OPERATION 8~9 MENU KEY OPERATION .......................................... 10 SPECIFICATIONS .................................................. 11 TROUBLESHOOTING ............................................. 12 pyRANAQ CDRCS91MP TROUBLESHOOTING Problem Cause Action Unit will not turn on (no power) Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage Check connections for prope

A. AMPLIFIER MODEL : PA-305 INTRODUCTION Thank you for purchasing PYRAMID the MODEL PA-305 P. A. AMPLIFIER. The unit has been designed using the latest electronic technology available. The unit will offer exceptional performance and reliability at an affordable price. The unit dilivers 100 watts of power and features 4 microphone input jacks, 70-volt line output, CD/AUX input jacks, selectable speaker impedance (4Q, 8Q, 16Q , 70V) output, five individnal source mixing controls, master volume

use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o’clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. when the crossover selector switch is in “low pass” mode, this control sets the upper frequency limit for audio program sent to the speakers. when the crossover selector switch is in “high pass” mode, this control sets the lower frequency limit for audio pro

For this reason, always choose a location in your vehicle which has low vibration, adequate ventilation, a minimum of dust, and no moisture. Be sure to mount the amp in such a manner as to allow reasonable airflow over the cooling fins. Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the mounting surface. If the mounting surface is carpeted, measure t