|
Anleitung Zusammenfassung
Hold it to skip forwards. B. During RADIO mode, press and hold or for more than 2 seconds you can manual search channel. Then press ►Hor ,you can have auto search channel. 5.APS BUTTON IN RADIO MODE: When short pressing, the radio searches for each preset station. When the field strength level is more than the threshold level of stop level, the radio is holding at that preset number for few secretary with releasing mute, and than searches again. In FM band, FM 1, FM 2 and FM 3 is checked one at a time. When long pressing (more than 1 second),the radio searches from the current frequency and checks the signal strength level until 1 cycle search is finished. And then 6 strongest stations are preset to the corresponding preset number. The AS operation is implemented in the each band of selected band. When the AS operation is finished, the radio executes the preset scan. 7.DSP BUTTON Press it to switch between 4 preset equalizer curves: FLAT,CLAS,POP M.ROCK M. The sound quality will be changed. 8.EJECT BUTTON Press it to eject the disc from the disc slot. 9.MODE BUTTON Press it repeatedly to select CDP, AUX and RADIO mode in sequence and circulation. For SUB WOOFER function(optional), press and hold for more than 2 seconds can have WOOFER Mode. 10-11-12-13-14-15. PRESET MEMORY BUTTONS A.To memorize the current frequency, press any one of the six preset Buttons hold for more than 2 seconds. B.To recall the preset memory, press one of the preset buttons [1-6]. 2 BASIC OPERATION C).ln CDP mode, press 1PAU button to pause CDP playing, press it again to resume CDP playing. D). In CDP mode, press 2SCN button to play the first 10 seconds part of each song, press it again to stop scanning and retain playing the song currently selected. E). In CDP mode, press 3RPT button to play the current track repeatedly. Press it again to cancel this mode. F). In CDP mode, press 4SHF button to play the track in random order. Press It again to cancel this mode. 16.SCAN BUTTON Press it to scan up by one channel step with station detection. If a valid signal has detected, the current frequency is blinked with in 5 seconds, then press it again to stop scan and remain the current frequency; otherwise, the unit continue to scan up by one channel step with station detection 5 seconds later. 17.CLOCK BUTTON Press it to display time on LCD for few seconds.Press it hold and then press m or button to adjust hour or minute. 18.MUTE BUTTON Press it to eliminate the sound immediately. 19.BAND BUTTON Press it to select your desired radio band and the band which is selected will be displayed on LCD. Press it hold for more than 2 seconds can have LOUD mode. LOUD MODE: When reduce the volume to half level, press it to enhance the bass effect. 20.POWER BUTTON Press it to turn on or off the unit. 21.FLASHING LED If the front panel is not on the main unit, LED will be flashing. 22.RESET RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons: -Initial installation of the unit when all wiring is completed. -All the function buttons do not operate. -Error symbol on the display. Note: If press RESET button, the unit can’t work yet, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel. 23.THE CHANGE-OVER SWITCH OF FREQUENCY(OPTION) Slide it youcan select theUSA orEUROPE radio frequency. 3 ELECTRIC CONNECTION WIRING CONNECTION NOTE: In spite ofhaving any kindsof speaker system, must use 4ohms impedance of speaker to reduce the distortion during high volume level. 4 INSTALLATION HEX NUT SPRING WASHER PLAIN WASHER TAPPING SCREW KEY PLATE PLASTIC TRIM OUT KEY PLATE 1.WHILE INSTALLING THE FRONT PANEL, PLEASE MOUNTTHE LEFTSIDE FIRST, AND MAKE THE DIRECTION HOLE ON THE FRONT PANEL AJM AT THE LEFT GUIDE ON THE UNIT 2.THAN PUSH THE RIGHT SIDE TO MOUNTTHE RIGHT GUIDE 3.PUSH ITTO INSTALLTHE FRONT FRONT PANEL COMPLETELY . 5 INSTALLATION CAUTION: DO NOT INSTALL THE DETACHABLE PANEL BEFORE CONNECTING THE WIRE. 1. The unit is designed for negative terminal of the battery which is connected to the vehicle metal. Please confirm it before installation. 2. If the car interior is extremely hot, as after being parked in the sun, do not use the player until the car has been driven fora while to cod off the interior. 3. Press the OPEN button to flip down the front panel (see fig.1), Slide the guide knob to remove the right side first, then take away the front panel, (see fig.2) and put it in the protective case (see fig.3) for safe keeping. 4. Install the front panel back into its bracket and then push it back to the position for playing (see fig.4). FRONT PANEL OPEN BUTTON (FIG.1) (FIG.2) PROTECTIVE CASE FRONT PANEL FRONT PANEL (FIG.3) (FIG.4) 6 NOTES DISC PLAY: CLEANING DISCS Before playing, clean the disc with a clean, lint-free. Fli...
Dieses Handbuch ist für folgende Modelle:Nailers - CDR78 (124.12 kb)