Features • Turns on lighting when motion is detected. • Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Bulb Holders Rubber Plug Plastic Hanger Cover Plate Sensor 2 Wire Connectors Mounting Bolt Mounting Strap Gasket 6 Screws (3 sizes included) Light Control Requirements • The light control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through

2. The light control may be picking up a heat source like an air vent, dryer vent, or brightly painted, heat- reflective surface. 3. Light control is in manual mode. 1. Heat or light from the flood lamps may be turning the light control on and off. 2. Heat being reflected from other objects may be turning the light control on and off. 3. Light control is in the TEST mode and warming up. 4. Light may be leaking through the flood lamp reflectors. Light control is detecting its own lights. 1. Turn

Flip the light switch off for one second then back on to toggle between AUTO and MANUAL MODE. Manual mode works only with the ON-TIME switch in the 1, 5, or 10 position. 240-026-A © 2008 Atlas Lighting Products, Inc. 598-1092-02 Mode Switching Summary TEST Move ON-TIME Switch to 1, 5, or 10 minutes AUTO Flip light switch off for one second then back on* MANUAL MODE * If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time the control

For best performance, mount the fixture about 8 ft.(2.4 m) above the ground.NOTE: If fixture is mounted higher than 8 ft.(2.4 m), aiming the sensor down will reduce coverage distance. Wall Mount Eave Mount For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock. For eave mount only: . Swing the sensor head towards the clamp screw joint. Controls Clamp Screw . Then rotate the sensor head clockwise 1

(1 m). Sensor Least Sensitive . Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. . Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times whenmotionisdetected).Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (25 mm) away from the bulbs. Most Sensitive Clamp Screw Ball Joint Aim Sensor Down for Short Coverage 4 598-1098-02 SPECIFICATIONS Range ............

(1 m). Sensor Least Sensitive . Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. . Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times whenmotionisdetected).Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (25 mm) away from the bulbs. Most Sensitive Clamp Screw Ball Joint Aim Sensor Down for Short Coverage 4 598-1098-02 SPECIFICATIONS Range ............

The Atlas Copco LS 14 Cut-off Saw and the LS 16 Cut-off Saw are delivered with 2 m 3/8” tail-hoses with .” Flat-Face quick-release couplings. The direct driven hydraulically powered design provides consistent speed and torque. It also enables underwater cutting. 5 English For precise and clean cutting jobs on roads, sidewalks and floors, the Atlas Copco LSC Cart for the Cut-off Saw is recommended. The use of the Cart gives a better working posture, and the cutting depth can be adjusted by means

... . . ....... . . . . ©Copyright 2005 ATLAS COPCO CONSTRUCTION TOOLS AB 2005-06 NACKA • SWEDEN No 3392 5042 01 1 English ! . INTRODUCTION ....................................................................................................................... 2 SAFETY INSTRUCTIONS ........................................................................................................ 2 Introduction to safety ...........................................................................

If your locomotives and cars use more then 2.5 Amps, it is necessary to split the layout in several power sections and feed each section with an extra "booster" which provides more amperage. Terminals C & D on your Commander can be used to wire in extra boosters. For more information about adding power stations to your layout, please see the DCC section of Atlas' web site at LIMITED ONE-YEAR WARRANTY Atlas Model Railroad Company, Inc. warrants that this Commander will be free from defects in mat

• Automatically controls existing post light. • Dual Light Level. • Photocell keeps the light off during daylight hours. This package includes: Post Light Adapter 3 Screws 3 Wire Connectors Requirements • The Light Control requires 120 volts AC. • If you want to use Manual Override, the control must be wired through a switch. • Some codes require installation by a qualified electrician. OPERATION Mode: On-Time Works: Day Night Test 5 Sec x x Auto 1, 5, or 20 Min x Manual To Dawn* x Accent 3,6 Hr