Prevents damage to crankshafts and piston cylinder walls by protecting exposed piston rod bolts, and at the same time, safely guides piston rods during removal and installation. TO REMOVE PISTON: 1. Remove nuts from piston rod bolts. 2. Place small adapters into prong ends and onto rod bolt ends. 3. Tap base of tool with palm of hand or hammer to break loose rod cap union. 4. Remove bottom rod cap and small adapters. 5. Place prong ends of tool onto piston rod bolts and push on base to rem

Models 9931, 8832, 8833: The coding switch in these models consist of eight or nine small switches, each of which can be placed in any of three different positions. (+, 0, -). See Fig. 2. Using a small screwdriver, set both the transmitter and receiver coding switchesidentically. (Your private code setting). DO NOT SET ALL THE SWITCHES IN THE SAME POSITION. EXAMPLE: FIGURE 2 NOT ALL + or 0 or - IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS

See Fig. 4. Replace the pushbutton wiring and tighten the screws. Be certain the antenna wire is hanging down vertically and the receiver terminal numbers printed on the receiver case match the numbers on the operator terminal strip. (1) D. Model 8832 - Double Door Garage 3 2 1 3 2 1 3 2 1 3 2 1 (2) (1) E. Model 8833 - Three Door Garage (1) (3) (2) 3 2 1 3 2 1 3 2 1 FIGURE 5 104388 B. If the operating distance drastically decreases, remove the battery access door See Fig. 1A, and replace the bat

A. Remove the access cover from the front of the transmitter by sliding the cover away from the top of the transmitter. (See Fig. 1A). B. Use a small screwdriver or knife to remove small door on back of receiver to gain access to coding switches. (See Fig. 1B) IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION. Note: If installing Allstar Classic Quik Code transmitter(s) with a 99xx or 88xx Allstar Rece

In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Warranty effective after July 1, 1998. For Information: Phone 610-873- 6900 info@allstarcorp. com FAX 610- 873-6953 all

After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 35 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. B. If the transmitter doesn’t activate the operator, check the coding switches on both the transmitter and receiver to assure an “exact” match. ( See Fig. 2 & 3) . This may necessitate a reprogramming of a Quik Code Classic transmitter to match the receiver coding swi

• LOCATE CONTROL PUSHBUTTONS WITHIN SIGHT OF THE DOOR AND AWAY FROM THE MOVING PARTS OF THE DOOR. INSTALL ENTRAPMENT WARNING LABEL NEXT TO THE CONTROL PUSHBUTTON IN A PROMINENT LOCATION. • REMOVE ALL ROPES AND REMOVE OR MAKE INOPERATIVE ALL LOCKS CONNECTED TO THE GARAGE DOOR. • THE IMPORTANT SAFEGUARDS AND INSTRUCTIONS IN THIS MANUAL CANNOT COVER ALL POSSIBLE CONDITIONS AND SITUATIONS. IT MUST BE UNDERSTOOD THAT COMMON SENSE AND CAUTION MUST BE EXERCISED BY THE PERSON(S) INSTALLING, MAINTAINING

Follow the directions on the next page for proper Transmitter/Receiver Coding! 733 Rotary Switch selects door A, B or C Slide Switch selects door A, B or C 8833C-OCS Rotary Switch selects door 1, 2, 3, ... or 9 639 Combination of both Rotary Switches selects door Examples: A1, B7, C9, etc. 831 STOP CLOSE OPEN 8833-OCS STOP CLOSE OPEN 535 COMMERCIAL TRANSMITTER MODELS Page 3 of 4 P/N 107343 Rev D The information below indicates how to set the coding switches in the various transmitters and receiv

This is accomplished by setting the selector switch on the transmitter to either 1, 2, 3, 4, 5, 6, 7, 8 or 9 and setting the #7 and #8 coding switches in the 831 receiver. Start coding by exactly matching all 8 code switches in the transmitter and receivers. The code switches may be set in any random pattern of +, 0 and - positions. Next, in receiver 1, set code switch #7 to + and code switch #8 +; In receiver 2, set code switch #7 to + and code switch #8 to 0. Continue setting the codes in the

Some models are designed to operate multiple receivers. A selector switch on the Transmitter determines which door will be controlled in a multi-door installation. The Receiver is connected to the commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. • ALLSTAR TRANSMITTERS ARE INTENDED FOR USE WITH COMMERCIAL DOOR OPERATORS ONLY. DO NOT USE FOR ANY OTHER PURPOSE. DO NOT MODIFY IN ANY MANNER. • CHECK LOCAL BUILDING AND ELECTRIC