. When the battery is fully charged, the pilot lamp will bilink in red slowly. (At 1-second intervals) (See Table 2) Table 2 Lamp indications Indications of the pilot lamp Charge status lamp (RED) Before charging Blinks (RED) Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) While charging Lights (RED) Lights continuously Charging complete Blinks (RED) Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) Charging impossible Flickers (RED) Ligh

66 METODO DE EXTRACCION E INSTALACION DE LA BATERIA ............................................ 66 METODO DE CARGA .......................................... 66 ANTES DE LA UTILIZACION .............................. 70 OPERACION ........................................................ 70 ALCANCE Y SUGERENCIAS PARA LA UTILIZACION ................................................ 78 MANTENIMIENTO E INSPECCION ........................ 79 ACCESORIOS ..................................................

A August, 1999 User’s Guide © 1999 Hitachi Koki Imaging Solutions, Inc. All rights reserved. No part of this document may be reproduced without the expressed permission of Hitachi Koki Imaging Solutions, Inc. The material in this document is for informational purposes and is subject to change without notice. Hitachi Koki Imaging Solutions, Inc., assumes no responsibility for errors or omissions in this document. No liability is assumed for any damages resulting from the use of the information it

Functions Date Places the date of copying on each copy. *The image area on which the date is printed may be erased. Page 1155O546AB Places a page number on each copy. *The image area on which the page number is printed may be erased. Distribution 1155O547AB Places a reference (distribution) number on the background of the copy, as assigned to each copy set. 1155O548AA Making Copies Chapter 3 Using Date Using Date 3-61 8. Auxiliary Functions Load your originals. Select whether to block out the ba

Original Size 1”(Inch) = 25.4mm 1mm = 0.0394”(Inch) 7-11 4. Description of Paper Size and Zoom Ratio Table Miscellaneous Chapter 7 Index-1 Index Numeric 100 Accounts ................................................. 4-19 1000 Accounts ............................................... 4-19 10-Key Pad .................................................... 2-14 1 1 ............................................................... 3-36 1 1 (2in1) ..................................................... 3-36

Please read and understand this manual before operating the power tool. Please keep this manual available for others before they use the power tool. MODE D'EMPLOI ET INSTRUCTIONS DE SECURITE_ _A AVERTISSEMENT_ Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la mort ou de sérieuses blessures corporelles ! Ce mode d'emploi contient d'importantes informations à propos de la sécurité de ce produit. Prière de lire et de comprendre ce mode d'emploi avant d'utiliser l'

g) Wenn Anschlusse fur Staubabsaug- und sammelvorrichtungen vorhanden sind, sorgen Sie dafur, dass diese richtig angeschlossen und eingesetzt werden. Die Verwendung solcher Vorrichtungen kann Staub-bezogene Gefahren mindern. 4) Einsatz und Pflege von Elektrowerkzeugena) Uberanspruchen Sie Elektrowerkzeuge nicht. Benutzen Sie das richtige Elektrowerkzeug fur Ihren Einsatzzweck. Das richtige Elektrowerkzeug erledigt seine Arbeit bei bestimmungsgema.em Einsatz besser und sicherer. b) Benutzen Sie d

1. Switch operation The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more. To turn the switch OFF, release the trigger switch to its original position. 2. Rotation + Striking This rotary hammer can be set to rotation and striking mode by pressing the push button and Fig. 6 turning the change lever to mark. (Fig. 6) (1) Mount the dr

7. NEVER operate without all guards in place. NEVER operate this tool without all guards or safety features in place and in proper working order. If maintenance or servicing requires the removal of a guard or safety feature, be sure to replace the guard or safety feature before resuming operation of the tool. 8. Use right tool. Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting tree lim