Improper use of this device in some applications may result in damage or injury. The user is urged to keep this book filed in a convenient location for future reference. These instructions may not cover all details or variations in equipment or cover every possible situation to be met in connection with installation, operation or maintenance. Should problems arise that are not covered sufficiently in the text, the purchaser is advised to contact Bristol for further information. EQUIPMENT APPLICA

The pushbutton switch is used to jump the load. 1. Adjust input test circuit for 4.995 V on DMM #1. 2. DMM #2 should read 20 mA. If necessary, adjust pot R50 to correct. 3. Press load pushbutton while observing DMM #2. If current reading increases, adjust R49 CCW. If reading decreases, turn it CW. Repeat procedure until change is less than ±.02 mA. 4. Final reading should be 20 mA, ±.02 mA. If necessary, reset pot R50 and repeat procedure. 5. Calibration is complete. Restore unit to normal opera

A 1/4 inch NPT vent is provided on the pressure regulator body for this purpose. The vent location is shown in Figure 2-3. When air is used as the pressure source, the vent fitting may be allowed to bleed into the atmosphere. If fuel gas or other hazardous type gases are used as the pressure source for a Remote Set Regulator, the VENT port must be piped to a safe location. ** Warning ** Covers of Remote Set Regulators operating in hazardous areas should not be removed. If servicing is required,

Removed all references to JIS specifications. Replaced SPS 4000 information with SPS 4001B information. Cover Updated photo, revision number and date. viii Removed Figure 3. Oxymitter 4000 with SPS 4000 Wiring Diagram from Quick Start Guide. 1-2 Revised Figure 1-1 to show SPS 4001B and updated IMPS 4000. 1-5 Revised Figure 1-2 to show SPS 4001B. 1-8 Added step 11 and Figure 1-6. 1-10, 1-11 Revised Figure 1-8 and Figure 1-9 to show SPS 4001B. 1-12 Removed Components paragraph. 1-13 Removed Figure

There are several occupational and non-occupational causes for pleural plaque. It should be noted that plaques are not “pre-cancer” nor are they associated with any measurable effect on lung function. Rosemount Analytical Inc. A Division of Emerson Process Management Instruction Manual IB-106-340C Rev. 4.1 July 2004 Hazardous Area Oxymitter 4000 TOXICOLOGY A number of studies on the health effects of inhalation exposure of rats and hamsters are available. Rats were exposed to RCF in a series of

Because these instruments are sophisticated technical products, you MUST properly install, use, and maintain them to ensure they continue to operate within their normal specifications. The following instructions MUST be adhered to and integrated into your safety program when installing, using, and maintaining Rosemount Analytical products. Failure to follow the proper instructions may cause any one of the following situations to occur: Loss of life; personal injury; property damage; damage to th

The standard application can be used with the appropriate Bristol® ControlWave® PLC/RTU, from Emerson Process Management to meet the I/O requirements at the various sites. The combined solution offers a cost effective system that is ready to deploy without the typical programming overhead. Benefits Pre-programmed package eliminates the need • for custom programming One package for one to three pumps provides • consistency for operators and technicians Local Display/Keypad Operator Interface pane

Description The Type 99 gas regulators provide a broad capacity for controlled pressure ranges and capacities in a wide variety of distribution, industrial, and commercial applications. A Type 99 regulator has a Type 61L (low pressure), Type 61H (high pressure), or a Type 61HP (extra high pressure) pilot integrally mounted to the actuator casing as shown in Figure 1. The Type 99 regulator can handle up to 1000 psig (69,0 bar) inlet pressures (the 1000 psig (69,0 bar) regulator requires a Type 13

Purge Air Specification....................................................................................................2-3 f. Regulated Air Specification.............................................................................................2-3 g. Calibration Gases Specification......................................................................................2-3 h. Sample Gas Specification...............................................................................................

All rights reserved. ELITE and ProLink are registered trademarks, and MVD and MVD Direct Connect are trademarks of Micro Motion, Inc., Boulder, Colorado. Micro Motion is a registered trade name of Micro Motion, Inc., Boulder, Colorado. The Micro Motion and Emerson logos are trademarks and service marks of Emerson Electric Co. All other trademarks are property of their respective owners. Contents Chapter 1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .