6,557,207; No. 6,760,947; No. 5,383,251; & Patents Pending Form No. 71071A 3/06 Clarke® Printed in the U.S.A. This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using i

3. Grasp at the bearing block and pull it out from the brush housing. 4. Remove the used brush. 5. Replace the used brush roller with a new one, or clean and remove all debris at the present brush. 6. Slide back the brush into the the fixed bearing block in the brush house. 7. Push the bearing block in its position. Lock it by turning clockwise. Always disconnect the power cord before performing any machine maintenance. FILTERS - type of filter may vary from different models At these machines th

If the red light (8) stays on continuously, there may be debris wrapped around the brush, during operation. At a double motor units this can cause the overload protector for the brush motor to trip. If this occurs, turn the Main Switch (17) OFF and unplug the power cord. Remove any debris from the brush and plug in the power cord, turn the Main Switch (17) back ON. This will automatically reset the overload protector. If the overload protector trips repeatedly contact your dealer for service. Fo

You must have training in the operation of this machine before using it. If youroperator(s) cannot read this manual, have it explained fully before attempting to operate thismachine. All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: Clarke® , 2100 Highway 265, Springdale, Arkansas 72764. English Espanol Francais EN ES FR 823 0102 040 Printed in China Edition 1 2007-11 2 Exploded view - Vue eclatee - Vista detallada Engl

DANGER! Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 be

3. Press the red "OFF" button or turn the key switch counterclockwise on machines equipped with key. 4. Put a brush or pad driver under the brush motor plate andalign the lugs on the motor with the slots on the brushgimbal. 5. Push the brush up and rotate counter direction to scrubrotation, until lugs lock (See Figure 20). 6. Reinstall brush housing if removed. DANGER: Operating a machine that is not completelyor fully assembled could result in injury orproperty damage. Do not operate thismachin

11. When you stop the machine, press the red "OFF" button or turn the key switch counterclockwise to the"OFF" position ("L" models only). Remove the keyand set the parking brake (if equipped). B How To Operate The Machine EN 5. When either the left or right forward/reverse switches(figure 28, item A) are pushed in, the machine will goforward ("L" models only). 6. Control the speed of traverse by using the traversespeed control knob ("L" models only) (figure 28, ItemC). 7. To stop, release the fo

3. Make sure the ramp is clean and dry. 4. Put the ramp in position. 5. Unfasten the machine. WARNING: The machine is heavy. Make sure you use two able persons to assist in moving the machine down the ramp. 6. On S17/S20 models, get two people to pull machine off ramp. It is recommended that the "S" model be unloaded in the forward position. 7. On the L17/L20 models only, turn the key switch "ON" and press the green "ON" button. Figure #2a 8. Set the traverse center knob to the slowest forward s

WARNING: Do not cut, remove or break theground pin. If the outlet does not fit the plug, consult your electrical contractor. WARNING: Have worn, cut or damagedcords replaced by an authorized service person. EXTENSION CORDS Use only an approved extension cord with three conductors, a plug with three terminals, and a connector body with three holes. The machine has a power cord with wire size 14 AWG (AWG means American Wire Gauge). WARNING: If you use an extension cord, use an extension cord with

71121A 1/06 Printed in the U.S.A. This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If your operator(s) cannot read this manual, have it exp