Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Clarke Dateigröße: 1.21 mb Dateiname: Clarke_Focus_Sm_Manual.pdf Unterrichtssprache:

3. Press the red "OFF" button or turn the key switch counterclockwise on machines equipped with key. 4. Put a brush or pad driver under the brush motor plate andalign the lugs on the motor with the slots on the brushgimbal. 5. Push the brush up and rotate counter direction to scrubrotation, until lugs lock (See Figure 20). 6. Reinstall brush housing if removed. DANGER: Operating a machine that is not completelyor fully assembled could result in injury orproperty damage. Do not operate thismachine unless it is completely assembled. Inspect the machine carefully beforeoperation. EN How To Prepare the Machine For Operation Figure 18 Figure 19 Figure 20 Page -16- Clarke® Operator's Manual -FOCUS S17/L17 and S20/L20 EN EN How To Remove Rotary Brush or Pad Driver (ifequipped) To remove the brush or pad driver from the machine, followthis procedure: 1. Turn the key switch clockwise ("L" models only). Press the green "ON" button. 2. Raise the brush head by pressing and holding thebrush up switch until brush head is in it's full up androtated position. 3. Press the red "OFF" button or turn the key switchcounterclockwise on machines equipped with key. 4 To remove brush, rotate brush in the same direction How To Prepare the Machine For Operation Figure 21 to scrub rotation with a quick snapping action untilbrush releases (See Figure 21). 5. Reinstall brush housing if removed. How To Change Or Rotate Cylindrical Brushes (ifequipped) To install or rotate brushes on the machine, follow this procedure: 1. Turn the key switch clockwise ("L" models only). Press the green "ON" button. 2. Raise the brush head by pressing and holding thebrush up switch until brush head is in it's full up androtated position. 3. Press the red "OFF" button or turn the key switchcounterclockwise on machines equipped with key. Go to front of the machine and remove thumb screw from brush door (See Figure 22). 5. Lower door approximately 1/2 inch and slide doorand bearing assembly off shaft (See Figure 23). 6. Remove brush spacer and brush by sliding off ofbrush shaft (See Figure 24). 7. Rotate brush or replace. 8. Slide brush on shaft and rotate slowly until drive pinsare lined up with brush slots. Push brush all the wayin. 9. Install brush spacer on shaft. 10. Slide brush door bearing assembly on shaft. 11. Raise door and install thumb screw. DANGER: Operating a machine that is notcompletely or fully assembled couldresult in injury or property damage. Do not operate this machine unlessit is completely assembled. Inspectthe machine carefully beforeoperation. Figure 22 Figure 23 Figure 24 Clarke® Operator's Manual -FOCUS S17/L17 and S20/L20 Page -17 EN EN How To Operate The Squeegee The squeegee wipes the floor while the vacuum motorremoves the dirty solution from the floor. Use your handto lower or raise the squeegee handle. To operate thesqueegee, follow this procedure: 1. To lower the squeegee and start the vacuum motor, move the squeegee lever to the right and down (Seefigure 25). 2. To raise the squeegee, lift the squeegee lever up(See figure 26.) NOTE: The center position lets the vacuum motorcontinue to run with the squeegee off the floor to avoiddrips and also allows you to back up the machine. How To Fill The Solution Tank The solution tank is filled at the rear of the machine (Seefigure 27). To fill the solution tank follow this procedure: 1. Add a cleaning chemical to the solution tank. For the correct amount of chemical, follow the directions shown on the container. 2. Remove the solution lid and fill the solution tank with water. WARNING: Water solutions or cleaning materials used with this type of machinecan leave wet areas on the floor surface. These areas can cause a dangerous condition for the operatoror other persons. Always putCAUTION signs near the area youare cleaning. WARNING: Machines can ignite flammablematerials and vapors. Do not use with or near flammables such as gasoline, grain dust, solvents andthinners. Use only a commerciallyavailable cleaners and concentrations intended for floor scrubbing applications. WARNING: Clarke recommends a maximum water temperature of 120oF (49oC). Operating The MachineNOTE: Put the machine in the lowest traverse speedsetting. Use the machine in an area that has no furniture or objects until you can do the following: 1. Move the machine in a straight direction, forward andbackward. 2. Stop the machine safely. 3. Turn the machine both left and right and return to astraight direction. To move the machine, follow this procedure: 1. Release the parking brake (if equipped with machine). 2. Turn the key switch clockwise to the "ON" position (on"L" models only). Press the green "ON" button. 3. Raise the brush to the highest setting. 4. Raise the squeegee. How To Operate The Machine Figure 25 Figure 26 Figure 27 Page -18- Clarke® Operator's Manual -FOCUS S17/L17 and S20/L20 EN 5. When either the left or right forward/reverse switches(figure 28, item A) are pushed in, the machine will goforward ("L" ...

Herunterladen

Geben Sie zwei Ziffern: