Adobe Systems 0–1300207782- 119FREQUENCY (MHz) AMPLITUDE ( dBFS) –10–20–30–40–50–60–70–80–90–100–110–1205101520fIN = 3.5MHz @ –1dBFSLNA = 6.VGAIN = 1VFILTER TUNEDHPF = 700kHz Figure 17. Typical FFT, AD9272/AD9273 USING THE INTEGRATED CROSSPOINT SWITCH (CW DOPPLER MODE) To examine the spectrum of the CW Doppler integrated crosspoint switch output, use the following procedure: 1. Complete the steps in the Configuring the Board and Using the Software for Testing sections to ensure that the board is
Populate R406 and R407 with 0 . resistors and remove R415 and R416 to disconnect the default clock path inputs. In addition, populate C405 and C406 with a 0.1 .F capacitor and remove C409 and C410 to disconnect the default clock path outputs. The AD9515 has many pin- strappable options that are set to a default mode of operation. Consult the AD9515 data sheet for more information about these and other options. PDWN To enable the power-down feature, short P303 to the on position (AVDD) on the PDW
The AD9272/AD9273 data sheet, available at provides additional information and should be consulted when using the evaluation board. All documents and software tools are available at For any questions, send an email to highspeed.converters@analog.com. TYPICAL MEASUREMENT SETUP Adobe Systems 07782- 001 Figure 1. AD9272-65EBZ/AD9272-80KITZ/AD9273-50EBZ Evaluation Board and HSC-ADC-EVALCZ Data Capture Board TABLE OF CONTENTS Features ..................................................................
Connect the included power supply along with the CLK and AIN signal sources to the two evaluation boards. Then connect to the PC via the USB port and evaluate the performance instantly. 2. USB Port Connection to PC. PC interface is via a USB 2.0 connection (1.1 compatible) to the PC. A USB cable is provided in the kit. 3. 64 kB FIFO. The on-board FPGA contains an integrated FIFO to store data captured from the ADC for subsequent processing. 4. Up to 644 MSPS SDR/800 MSPS DDR Encode Rates on Each
02062-9106 a Copyright Information ©2007 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written consent from Analog Devices, Inc. Printed in the USA. Limited Warranty The EZ-KIT Lite evaluation system is warranted against defects in materials and workmanship for a period of one year from the date of purchase from Analog Devices or from an authorized dealer. Disclaimer Analog Devices, Inc. reserves the right to change this product
Cr, Cb: 0.7 Vp/p. Impedance: 75 Ohm. • S.VIDEO Connector: 4-pin mini DIN female. Standard: PAL : 15.625 kHz / 50 Hz - 625 lines. NTSC : 15.734 kHz / 59.94 Hz - 525 lines - 7.5 IRE. Level: Y : 1 Vp/p (0.7 V Luma + 0.3 V Sync.). C : 0.7 Vp/p (0.3 V Chroma Burst). Impedance: 75 Ohm. • COMPOSITE VIDEO Connector: BNC female. Standard: PAL : 15.625 kHz / 50 Hz - 625 lines. NTSC : 15.734 kHz / 59.94 Hz - 525 lines - 7.5 IRE. Level: 1 Vp/p (0.7 V Luma + 0.3 V Sync.). Impedance: 75 Ohm. • FRAME LOCK Conn
..[23.97 Hz] ..[24 Hz] ..[25 Hz] ..[29.97 Hz] ..[30 Hz] ..[50 Hz] ..[59.94 Hz] ..[60 Hz] ..[Frame lock]: The output frame rate is synchronized onto the frame rate of the signal connected to the genlock input. PAGE 22 BROAD SCAN (HD/SDI) Chapter 4 : FRONT PANEL DISPLAY MENU DESCRIPTION (continued) 4-5. FUNCTIONS DESCRIPTION (continued) ..[Genlock Tune]. This function is available only if the Output format selected is Genlock, and if a correct genlock signal is detected on the GENLOCK INPUT connec
Please follow all of the warnings on this product and its operating instructions. CAUTION: WARNING: To prevent the risk of electric shock and fire, do not expose this device to rain, humidity or intense heat sources (such as heaters or direct sunlight). Slots and openings in the device are provided for ventilation and to avoid overheating. Make sure the device is never placed on or near a textile surface that could block the openings. Also keep away from excessive dust, vibrations and shocks. PO
SETTINGS........................................................................................................................................................................16 2-3. IMAGE ADJUSTMENTS ................................................................................................................................................16 2-4. EMBEDDED AUDIO MODE...............................................................................................................................
BROAD SCAN HD (BHD930) REAR PANEL DESCRIPTION O / I: AC power switch (O = OFF, I = ON). POWER: Standard IEC connector (100-250 VAC, 0.5A, 50-60Hz automatic). RS-232: RS-232 communication port on a DB9 female connector. IP/LAN: Ethernet communication port on a RJ45 connector (optional). COMPUTER INPUT & MONITOR AUDIO IN: Analog stereo audio input on 2x RCA female connector (L = Left, R = Right). RGB INPUT: Analog computer input on HD15 female connector. RGB MONITOR OUT: Analog computer output (lo