In addition, the heater's low mass allows rapid start-up and fast response to controls. The patented RAYMAX heater features one-inch (25 mm) wide emitter strips that are individually replaceable for lower maintenance costs. Weighing only 5.5 lbs/ft2 (26.8 kg/m2), the heater is easy to mount. Applications • Thermoforming • Textile drying • Paint curing • Powder coating fusing • Shrink wrapping • Circuit board soldering Aluminized Steel Case Features and Benefits Replaceable emitters •

Other voltages are available. Terminals: Non-standard locations are also available. Please specify. Standard Dimensions: ±Xe inch (0.0625 mm) Typical Peak Energy Wavelength: 3-3.5 microns Specifications Heater Dimensions Min. Max. Increments Width: inches (mm) Length: inches (mm) Area: in (cm ) 1 (25.4) 6 (152.4) 6 (38.7) 36 (914.4) 70 (1778) 864 (5574.2) 1 (25.4) any any Note: Less than maximum length X width may exceed maximum area. How to Order To order your stock RAYMAX heater, spe

Louis, Missouri 63146 USA Phone: (314) 878-4600 FAX: (314) 878-6814 Internet: e-mail: info@watlow.com © 2001 Watlow Electric Manufacturing Company FAX-1900-1100

It makes use of the most advanced heater construction techniques including embedding a nickel chromium element wire in Watlow's exclusive mineral insulation.Only 0.042 inches (1.067 mm) thick, this layer of insulation brings the element wire closer to the heater sheath.The result is heat flows easily from the element wire to the sheath, thus allowing the wire to run cooler than conventional heaters. Performance Capabilities • Sheath temperatures to 1400°F (760°C) • Watt densities to 100 W/in2

A mere 15 mils (0.4 mm) thick mica insulator on both sides of the resistance element provides complete electrical insulation and offers little resistance to efficient heat flow. Plus mica withstands high voltage spikes, resists moisture and is inert to most chemicals. UL® component recognition is available for applications to 900°F (480°C) sheath temperature, file number E52951. Performance Capabilities • Sheath temperatures to 900°F (480°C) on zinc-coated units • Sheath temperatures of 1200°

Consult your Watlow representative if vertical mounting is unavoidable. • Mount the heater near or below the lowest point on the engine block. Keep outlet nozzle pointed up, as indicated on the tank. Estimate kilowatt requirements with the following formula. First determine the engine displacement, then multiply: English Cubic inches X 3 = estimated wattage Metric Liters X 183 = estimated wattage Outlet Nozzle Sized for 1" I.D. W- 20 Mounting Bolts Vibration Isolator Bushings (2) Mountin

The opposite end is sealed to resist contamination. Standard 305 mm (12 in.) flexible lead wires are crimp connected to the terminal pin and have silicone impregnated fiberglass oversleeves. With its round cross-section geometry, the double-ended WATROD is highly adaptable for bending – especially when bending is performed in the field. Both single- and double-ended WATRODs share many construction features that deliver long life—the resistance wire is centered in the heater sheath and electrical

The maximum recommended surface temperature of the heater is based on the rating of the ceramic fiber heater module. This can vary from 1095°C (2000°F) at lower watt densities, to higher watt densities at reduced surface temperatures. Note that maximum wattages cannot be achieved at the maximum Width: inches (mm) 2 (51) 30 (760) Any Length: inches (mm) 6 (152) 52 (1320) Any Note: Units will be 1.4 inch (6 mm) wider than the nominal size of the HHeeaatteerr DDiimmeennssiioonnss MMiinn.. MMaaxx..

Each unit consists of a ceramic fiber heater mounted in a 2.5 inch (64 mm) deep sheet metal case that provides thermal insulation. The case includes post terminals for electrical connections and provides a mounting system that can be used with virtually any flat ceramic fiber unit, whether it is a stock, standard or a custom size. Since any of the flat unit heating element configurations can be used—exposed sinuated, embedded coil or foil elements— watt density and temperature capabilities can b

Watlow developed a unique compacted mineral insulation to electrically insulate the element wire, with a result of superior heat transfer and higher operating capabilities. Because of its rugged stainless steel construction, the RAYMAX 1330 will last longer. And this relatively new heater features a high emissivity black coating and a uniform, full surface heat source for better efficiency. Applications • Thermoforming plastics and composites • Circuit board soldering • Heat shrinking of pl