Code can easily be changed if desired. Operation: Opener activates when 4-digit code and ENTER button are pressed. If wrong numbers are accidentally pressed, correction can be made immediately. The ENTER key will transmit only the last four digits. The keypad will blink for 15 seconds after the code is transmitted. During that time you can STOP or REVERSE door travel just by pressing the ENTER key. The Multi-Function Keyless Entry can be used with any 'SMART' receiver. The keypad will illumi

Make sure Tab\ (Fig. 2) locks into place in new position, 4. Turn Shaft & Cam Assembly in a clockwise direction until switch lever arm is on top of Tab to assure that both mechanism switches are open (Fig. 3) 5. Reconnect power to machine. CAM NOTCH ÖSE FINGER TO LIFT TAB FIGURE 2 FIGURE 3 P/N 134411800(0403)

¦ Do not touch hot surfaces. Use potholders when removing cover or handling hot containers. ¦ To protect against electrical shock, do not immerse cord, plug or base unit in water or other liquid. ¦ Close supervision is necessary when any appliance is used by or near children. ¦ Unplug from outlet when not in use. Allow to cool before cleaning. ¦ Do not operate appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner. Return appliance to an auth

THERE ARE NO OTHER USER SERVICEABLE PARTS. The 53000 Series remote control (with green battery test light) works only with door openers and light controls having a green "SRT" button and green indicator light. Instructions are given below for programming your opener to match the remote control's code. The additional remote control buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with those accessories.) 53000

All the codes the opener has learned will be erased. • To reprogram, repeat Steps 1, 2 and 3 for each remote control in use. Replacement Parts: 12 Volt battery -10A14; Compact remote control case, cover and Velcro strip (circuit board not included) - 41A3592; 3-Function remote control case, cover, screw (circuit board not included) - 41A3888; Visor Clip - 29C128 Select a remote control push button to operate opener Figure 2 Garage Door Opener (With Green "SRT" Button) [ M Су Çy / \ |7i

SAFETY CONSIDERATIONS Installing and servicing air conditioning equipment can be hazardous due to system pressures, electrical components, and fuel gases. Only trained and qualified personnel should install, service, or repair air conditioning equipment. Untrained personnel can perform basic maintenance functions such as cleaning coils, or cleaning and replacing filters. All other operations should be performed by trained service personnel. When working on air conditioning equipment, observe pre

Follow all safety codes. Wear safety glasses and work gloves. Have a fire extinguisher available. INTRODUCTION These instructions cover the installation of an Accessory Crankcase Heater on Electric Cooling, Heat Pump and Electric Cooling/Gas Ideating units. _) DESCRIPTION AND USAGE The accessory crankcase heater warms the compressor crankcase oil to reduce refrigerant migration in the crankcase and ensure proper compressor lubrication. Refer to Tables 1, 2 and 3. INSTALLATION Instructions CPCRKH

l_Typical Crankcase Heater Installation C01015 c CH c -BLK---_ LEGEND C CH -- Compressor Crankcase Contactor Heater <_) Marked Terminal C01014 Fig. 2--Crankcase Heater Wiring 7. Connect 11, and terminal one black lead to the connect other black 21. (See Fig. 2.) compressor contactor lead to compressor terminal contactor 9. Replace 10. Turn on access main panel. power, then (if applicable) gas supply. 8. Attach control green box. crankcase heater ground lead to ground screw in Copyright 2001 Card

above compressor mounting 1. Turn off gas supply (if applicable) first, then disconnect plate. (See Fig. l.I electric power supply. 5. Fasten heater firmly in place with fastening clip provided with 2. Install Lockout Tag, the crankcase heater. (See Fig. 1.1 6. Route crankcase heater leads into unit control box, following Fig. 1.) the path of the compressor leads. (See Fig. 1.) 3. Remove access panel for compressor and control box. (See Manufacturer reserves the right to discontinue, or change a