It also serves as a battery level indicator. 5. Use the Footswitch to activate/deactivate the effect. 6. Use this 1/4 TS IN connector to plug in the instrument cable. 7. The 1/4 TS OUT connector sends the signal to your amp. Use the DC IN connection to plug in a 9v power supply (not included). The Battery Compartment is located underneath the pedal cover. To install or replace the 9v battery, press the hinges with a pen and remove the pedal cover. This effects pedal has no on/off switch. A

It also serves as a battery level indicator. 5. Use the Footswitch to activate/deactivate the effect. 6. Use this 1/4 TS IN connector to plug in the instrument cable. 7. The 1/4 TS OUT connector sends the signal to your amp. Use the DC IN connection to plug in a 9v power supply (not included). The Battery Compartment is located underneath the pedal cover. To install or replace the 9v battery, press the hinges with a pen and remove the pedal cover. This effects pedal has no on/off switch. A

High distortion settings will allow for extremely long sustaining tones. 5. The ON/BATT LED illuminates when the effect is activated. It also serves as a battery level indicator. 6. Use the Footswitch to activate/deactivate the effect. 7. Use this 1/4 TS IN connector to plug in the instrument cable. 8. The 1/4 TS OUT connector sends the signal to your amp. Use the DC IN connection to plug in a 9v power supply (not included). The Battery Compartment is located underneath the pedal cover. To

At minimum position no modulation effect is produced and the Wah effect is controlled by your playing intensity only. 3. The MANUAL control adjusts the basic frequency where the effect starts working. High MANUAL settings will decrease the sweep range, because the low end of the frequency sweep is moved upwards. 4. The SENS control adjusts the sensitivity of the effect. Nearing maximum position you achieve Wah effect even with soft playing, nearing minimum position the Wah effect will not be

High distortion settings will allow for extremely long sustaining tones. 5. The ON/BATT LED illuminates when the effect is activated. It also serves as a battery level indicator. 6. Use the Footswitch to activate/deactivate the effect. 7. Use this 1/4 TS IN connector to plug in the instrument cable. 8. The 1/4 TS OUT connector sends the signal to your amp. Use the DC IN connection to plug in a 9v power supply (not included). The Battery Compartment is located underneath the pedal cover. To

It can be used to achieve effective volume boost or cut . 3. The ON/BATT LED illuminates when the effect is activated. It also serves as a battery level indicator. 4. Use the Footswitch to activate/deactivate the effect. 5. Use this 1/4 TS IN connector to plug in the instrument cable. 6. The 1/4 TS OUT connector sends the signal to your amp. Use the DC IN connection to plug in a 9v power supply (not included). The Battery Compartment is located underneath the pedal cover. To install or repl

The black wire should have a #6 ring terminal crimped on (not supplied) and connected to chassis ground. Caution while Installing the Antenna • Install the antenna onto the inside glass so it does not fall down while driving. • Install on a clean glass surface. Moisture can cause the antenna to fall down. • Low temperature decreases the adhesion. Therefore, turn on the heater if temperature is below 68 degree Fahrenheit. • Do not touch the sticky part of the tape. • Keep the distance betwe

INPUT – 1/4” input connector. 2. PARA OUT – It’s parallel output 1/4” jack for passing the input signal through to a stage amplifier or monitor system. 3. ATT Switch – input attenuation, switchable(0dB,-20dB,-40dB) 4. BALANCED OUTPUT – Male XLR connector. 5. GROUND – When engaged, the ground from the PDC21 chassis detaches from the XLR jack. -1 Operating the PDC21 Operating the PDC21 A direct box, or DI box, provides the facility for the direct insertion of an audio signal into a mixer or record

times is increased when control is turned clockwise and decreased when turned counterclockwise . 2. FEEDBACK knob This controls the amount of feedback. delay effect will increase by turning it clockwise and decrease by turning it counterclockwise. 3.D.LEVEL knob Controls the level of delay. Effect is increased by turning clockwise and decreased by turning it counterclockwise. 5 4. Output Jack The output jacks are used to connect the unit to amplifiers or other devices. 5. AC Adaptor Jac

<^>pyU5 PRO PPDLWW1 WAH WAH PEDAL 1. The SIGNAL OUTPUT is used to connect to the amplifier 2. The SIGNAL INPUT connects to the instrument 3. DC9V POWER PLUG can be used to power the pedal 4. The PEDAL is used to control the effect 5. ON/OFF switch 6. 9 Volt REPLACEABLE BATTERY SPECIFICATIONS: - Designed for Electronic Guitars - Includes Instrumental and Amplifier 1/4” Ports - Rubber Bottom Floor Grips 4 - True Bypass Switch - Includes 9V 6F22 replaceable battery - Battery Life