Determine pivot location using dimensions on reverse side. Depth of mortise in the bottom of door will determine clearance. Be sure to properly locate and mark pivot center point of the base plate. Locate, drill, and tap 1/4-20 mounting holes for metal door. Locate and drill pilot holes for #14 wood screws for wood door. Mount door leaf in bottom of door with 1 /4-20 x 3/4” FHMS or #14 FHWS screws provided. Locate, drill, and tap mounting holes for jamb base plate. Pivot point of top pivot set

Our commitment to quality makes IVES a name you can trust. FLEXIBLE DOOR STOP FOR USE ON WALLS TO STOP DOOR AND PREVENT DAMAGE TO WALL, DOOR AND DOOR KNOB. SHOCK ABSORBING RUBBER TIE INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Phillips screwdriver, awl or pencil. 1. Locate stop in the center of baseboard and approximately 1" from door edge and mark. 2. Secure base with screw provided. 3. Attach flexible spring to base. ASK FOR OTHER FINE HARDWARE BY H.B. IVES a e WINDOW LOCKS DOOR

Our commitment to quality makes IVES a name you can trust. SCREEN DOOR PULL FOR USE ON WOOD SCREEN DOORS. MAY ALSO BE USED AS A PULL OR HANDLE ON DRAWERS AND CABINETS. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Phillips screwdriver, awl or pencil. FOR DOOR APPLICATION (Illustration 1): 1. Position in desired location and mark. 2. Secure with screws provided. FOR DRAWER APPLICATION (Illustration 2): 1. Position in desired location and mark. 2. Secure with screws provided. ASK FOR OTHER

Our commitment to quality makes IVES a name you can trust. CHAIN DOOR GUARD FOR USE ON INTERIOR OR EXTERIOR DOORS FOR ADDED SECURITY. FEATURES WELDED STEEL CHAIN. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill, Vie” drill bit, Phillips screwdriver, awl or pencil. 1. Position plate (A) approximately 52" from bottom of door. Mark, drill pilot holes, and secure. 2. Position chain holder (B) at same height as plate. Before securing chain holder, make sure distance between chain holder and pla

Determine pivot location using dimensions on reverse side. The pivots are handed. To determine hand of door and proper pivot position, see diagrams above. 2. Locate, drill, and tap 1/4-20 mounting holes for metal door or metal frame. Locate and drill pilot holes for #14 wood screws for wood door or wood frame. Install pivot leafs with 1/4-20 x 3/4” FHMS or #14 FHWS screws provided. 3. Loosen set screw in pin leaf with 3/32” Allen wrench provided and remove pivot pin. 4. With door in open posi

Follow all instructions carefully. For questions contact Technical Support at 1-888-371-7331. I*"7 Ingersoll Rand 13103 Rev. 4 © 2006 Ingersoll-Rand Company Limited Security Technologies NOTE It is very important for installer to verify that intermediate pivot point lines up with center line of top and bottom pivot points before final installation. Both door and frame pivot leafs located from face of door. Intermediate pivot should be evenly spaced between top and bottom pivots. Heel edge of

Determine pivot location using dimensions on reverse side. The pivots are handed and must match hand of door. To determine hand of door and proper pivot position, see diagrams above. Install top and bottom pivot sets before installing intermediate pivot. 2. Locate, drill, and tap 1/4-20 mounting holes for metal door. Locate and drill pilot holes for #14 wood screws for wood door. Then hang door. 3. Open door about 90°. Install pivot leafs with 1/4-20 x 3/4” FHMS or #14 FHWS screws provided. 4

Our commitment to quality makes IVES a name you can trust. MORTISE BOLT FOR USE ON DOORS FOR ADDED SECURITY. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill, W, W, VV drill bits, Phillips screwdriver pencil and chalk. L Position wdt approximately 45* to 60" from bottom of door on center of door eage. Mark and drill Vi«' hole 2W deep (A). 2. DrillW hole W deep and IV/ from edge of door (B). 3. Place bolt in brfe (A) insert knob shaft in hole (B) to align with (C). Mark, drill and secure t

Our commitment to quality makes r\'ES a name you can trust. SUPER-MITE® MAGNETIC CATCH DUAL TRIPLE POLE FOR USE ON LARGE CABINET AND FULL LENGTH DOORS. FEATURES HEAVY DUTY DESIGN WITH EXTRA STRENGTH HOLDING POWER. INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill, Vis" drill bit, Phillips screwdriver, awl or pencil. FOR SINGLE DOOR APPLICATION (Illustration 1): 1. Po'sition case (A) on top corner or side of door frame. 2. Mark, drill pilot holes in center of elongated holes (B) and secur