Hood installation notes: See Figure 4.8. NOTE: Use this procedure for more extensive repairs. Typical reasons may include dash panel removal, or the need for more working room than simply removing the hood will provide. 4.1. Remove the battery: See Figure 4.1. Figure 4.1 • Disconnect the negative battery cable (black) first, using a 7/16” wrench. • Disconnect the positive battery cable (red) using a 7/16” wrench. • Remove the battery hold-down. • Lift the battery from the tractor. 4.2. D

The slots in the ends of the bar will fit over the spacers. Support the hood with an improvised prop rod. Install the screws that hold the hinge support bar to the dash support and instrument panel. Snap the hood support cylinder into place, and remove the prop rod. The remainder of the installation process is simply the reversal of the removal steps. 6

(Plug secured to the hood lift cylinder). 4.3. Support the hood with an improvised prop-rod to prevent damage. 4.4. Remove screws holding hinge support bar to dash support using a 1/2” wrench. 4.5. Disconnect and remove the hood lift cylinders using a small straight-blade screwdriver. 4.6. Remove screws & flat washers holding hinge support bar to dash panel using a 3/8” wrench. 4.7. Lift hood and hinge assembly off of the tractor, and remove it to a safe place. Figure 4.8 Position the hin

v Please keep these operating instructions in a safe place. Contents 1. Where to Use Your GARDENA Cylinder Lawnmower . . . . . . . . . 8 2.For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Esta restricao valera tambem para pecas adicionais e acessorios. K Produktansvar Vi gor udtrykkeligt opm.rksom pa at i henhold til produktansvarsloven er vi ikke ansvarlige for skader forarsaget af vores udstyr, hvis det skyldes uautoriserede reparationer eller hvis dele er skiftet ud og der ikke er anvendt originale GARDENA dele eller dele godkendt af os, eller hvis reparationerne ikke er udfort af GARDENA-service eller en autoriseret fagmand. Det samme g.lder for ekstra udstyr og tilbehor. Deu

2. Safety instructions v Please read the notes on safety on the Cylinder Lawnmower. Warning! Warning! V Please read the opera- Sharp blades! ting instructions before using the mower! Danger! V Remove the key before carrying Risk of injury! out all maintenance work. V Keep bystanders away! 12 Checks before each operation: Before use, an inspection is always to be performed in order to determine that all nuts, bolts and working tools are not worn down or damaged. Worn down or damaged blades are to

BOX 368023 CLEVELAND, OHIO 44136-9722 [FORM NO. 770-10449 (9/00) CONTENTS Overview ......................................................................3 Safe Operation Practices .............................................3 Assembly Instructions ..................................................5 Operating Instructions .................................................6 Using the Accessories .................................................7 Working with Detergents ............................

For at undga skader pa maskinen eller andre materielle dele ma Accu cylinderklipper aldrig rengores med rindende vand eller hojtryksrenser. Achtung! Verletzungsgefahr durch scharfes Schneidwerkzeug – Finger und Fu.e entfernt halten! Warning! Risk of injury. Keep fingers and feet away from sharp cutting tool! Attention ! Risque de blessures par le cylindre de coupe – ne mettez ni mains ni pieds a proximite ! Let op! Verwondingsgevaar door scherp snijgereedschap – vingers en voeten weghouden! Varn

BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-03885 (February 19, 2008) Assembly & Set-Up 3 Contents of Carton • One 42" Timing Deck Striper/Roller One Operator's Manual Assembly NOTE: On older model decks the holes used to attach the Striper/ Roller to the mowing deck will have to be drilled in order to install the attachment. 1. Remove the attached carriage bolts and flange nuts from the mounting bracket. See Fig. 1-1. Flange Nuts Carriage Bolts Figure 1-1 NOT

carburetor), keep clear of all moving parts. Be careful of heated surfaces and muffler. Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If adjustment is needed, refer to the separate engine manual packed with your shredder. Hi^NOTE A DIRTY AIR CLEANER WILL CAUSE ENGINE TO RUN ROUGH. BE CERTAIN AIR CLEANER IS CLEAN AND ATTACHED TO THE CARBURETOR BEFORE ADJUSTING CARBURETOR. DO NOT MAKE UNNECESSARY ADJUSTMENTS. FACTORY SETTINGS