A SPARK NEAR THE BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY: a. Check the polarity of the battery post. The POSITIVE (POS, P, +) usually has a larger diameter than the NEGATIVE (NEG, N, -) post. b. Attach at least a 24 inch long 6-gauge (AWG) insulated battery cable to the NEGATIVE (NEG, N, -) battery post. c. Connect the POSITIVE (RED) charger clamp to the POSITIVE (POS, P, +) post of the battery. d. Position yourself and the free end of the cable as far

DANGER. Before using adapter as illustrated, be certain that center screw of outlet plate is grounded. The green-colored rigid ear of lug extending from adapter must be connected to a properly grounded outlet, make certain it is grounded. If necessary, replace original outlet cover plate screw with a longer screw that will secure adapter ear lug to outlet cover plate and make ground connection to grounded outlet. MOUNTING: The Battery Charger may be set on a table or a shelf. Do not set charger

This manual contains important safety and operating instructions for battery charger you have purchased. You may a later date. 2. CAUTION. To reduce risk of injury, charge only wet cell, lead-acid, automotive type rechargeable batteries. Other types of batteries may burst causing 3. Do not expose the charger to rain or snow if specifically warned on the unit not to do so. 4. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric sh

The POSITIVE (POS, P, +) usually has a larger diameter than the NEGATIVE (NEG, N, -) post. b. Attach at least a 24 inch long 6-gauge (AWG) insulated battery cable to the NEGATIVE (NEG, N, -) battery post. c. Connect the POSITIVE (RED) charger clamp to the POSITIVE (POS, P, +) post of the battery. d. Position yourself and the free end of the cable as far away from the battery as possible, then connect the NEGATIVE (BLACK) charger clamp to the free end of cable. e. Do not face the battery when mak

However if the clamps are removed while the charger is charging, a spark can occur. It is always best to unplug the charger from the electrical outlet BEFORE removing the clamps from the battery. UPPER BATTERY VOLTAGE LIMITS: The INTELLAMATIC™ charger will not start charging if the battery voltage is above 13.5 volts, this prevents overcharging a battery with a high surface charge. An absolute upper limit of 16 volts has also been included, which applies to 12 volt batteries, and 8 volts for 6 v

The Company hereby warrants to the Purchaser that if the Product, or any part thereof, shall prove to be defective due to improper workmanship or materials at any time up to and including one (1) year from the date of Product's purchase at retail, then the Company shall repair or replace the Product, or any part thereof, as the case may be, at the Company's option, without charge to the Purchaser for parts and labor, provided that Purchaser follows the procedures set forth herein. This limited w

9014 — SELECT SETTING switch with the following selections; OFF, 10A–12V AUTO, 2A–12V AUTO and 10A–6V MANUAL 9060 — SELECT SETTING switch with the following selections; 55A START, 10A–12V, 2A–12V and 10A–6V MANAUL — SELECT FUNCTION switch with following selections; CHARGE and START — Charge Complete Indicator light. — Reverse connection indicator light. 9070 — SELECT SETTING switch with the following selections; 70A START, 12A–12V, 2A–12V and 12A–6V — SELECT FUNCTION switch with following select

! Start the vehicle with the charger connected to the battery. NOTE: Do not crank the engine more than 20 seconds in any five minute period; excessive cranking may overheat and damage the starter. If the vehicle fails to start, while waiting for the starter to cool, allow the charger to continue to charge the battery. Unplug the charger before disconnecting dc clips from battery. POSSIBLE CHARGING PROBLEMS: 1. ! Meter needle swings to far right side of meter: (Manual). ! Reverse connection indic

Do not operate charger in a closed-in area, or restrict ventilation in any way. e. Do not set a battery on top of charger. 16. DC CONNECTION PRECAUTIONS a. Connect and disconnect dc output clips only after setting any charger switches to off position and removing ac cord from electric outlet. Never allow clips to touch each other. b. Attach clips to battery posts and twist or rock back and forth serval times to make a good connection. This tends to keep the clips from slipping off terminals and

SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions for models 9006, 9010, 9014, 9050, 9060, 9070 & 9090. You may need to refer to these instructions at a later date. 2. CAUTION. To reduce risk of injury, charge only wet cell, lead-acid, automotive type rechargeable batteries. Other types of batteries may burst causing personal injury and property damage. 3. Do not expose charger to rain or snow. 4. Use of an attachment not recommended or sold by the battery