GARDENA Grass collecting bag Saves raking up the cut grass. Art. No. 4029 9. Technical Data Cutting width / Cutting height Cutting height adjustment Weight 300 (Art. No. 4020) 30 cm / 12 – 42 mm infinitely variable 8.0 kg 380 (Art. No. 4023) 38 cm / 12 – 42 mm infinitely variable 8.5 kg 10. Warranty GARDENA guarantees this product for 2 years (starting from the date of purchase). This guarantee covers all serious defects of the unit that can be proved to be material or manufacturing faults. Unde

For safety reasons, children under the age of 16 as well as persons not familiar with these operating instructions should not use this cylinder lawnmower. v Please keep these operating instructions in a safe place. Contents 1. Where to Use Your GARDENA Cylinder Lawnmower . . . . . . . . . 8 2.For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Calle Colonia Japonesa s/n (1625) Loma Verde Escobar, Buenos Aires Phone: (+54) 3488494040 info@argensem.com.ar Australia Nylex Consumer Products 50-70 Stanley Drive Somerton, Victoria, 3062 Phone: (+61) 1800 658 276 spare.parts@nylex.com.au Austria / Osterreich GARDENA Osterreich Ges.m.b.H. Stettnerweg 11-15 2100 Korneuburg Tel.:(+43) 2262 7454536 kundendienst@gardena.at Belgium GARDENA Belgium NV/SA Sterrebeekstraat 163 1930 Zaventem Phone: (+32) 27209212 Mail: info@gardena.be Brazil Palash Co

Diese Garantieleistung bezieht sich auf alle wesentlichen Mangel des Gerates, die nachweislich auf Materialoder Fabrikationsfehler zuruckzufuhren sind. Sie erfolgt durch die Ersatzlieferung eines einwandfreien Gerates oder durch die kostenlose Reparatur des eingesandten Gerates nach unserer Wahl, wenn folgende Voraussetzungen gewahrleistet sind: . Das Gerat wurde sachgema. und laut den Empfehlungen in der Gebrauchsanweisung behandelt. . Es wurde weder vom Kaufer noch von einem Dritten ver sucht,

v Only work when visibility is good. v During use do not tip the unit and do not open the rear flap. v Familiarise yourself with the surroundings of your working area. Check for possible risks which might be not audible due to the noise of the machine. v Wear sturdy shoes and long trousers to protect your legs. v Ensure you keep your feet a safe distance from the moving parts. v Make sure that there are no other people (especially children) or animals anywhere near the working area. v Always pus

Remove point from welded tooth shank by hammering at “A” on tooth point or by driving a chisel at “B”, just between tooth point box section and tooth shank. Install new point and anchor it to shank by peening at location shown. It a tooth shank breaks off, becoming lost or damaged so that is cannot hold a tooth point, a new shank should be welded to bucket. TIGHTENING NUTS AND BOLTS Periodically check to be sure all bolts and nuts are tight (See Torque Chart). Check all pivot pins for cotter pin

It is convenient in many cases to work in 300 foot sections. Move the first Danger sign to the beginning of the freshly cleared area, place it, then take the first cutting area flag up to the end of the freshly cleared area 300 feet away. Walk and inspect the next 300 feet and place the second cutting area flag. Pick up the second DANGER sign, and take it a further 300 feet along the road or trail. Note that in many cases the DANGER area will extend in front of and behind the machine as well as

Make certain that the hole cut is far enough over that it will not interfere with operators foot room. Cut hole through floor mat and floor using a round 2" hole saw (See Figure 12). After you cut the rubber mat with the hole saw pull the piece of rubber out of saw, this will make it easier to cut through the floor. (See Figure 12) 3. Install Cable / Wire Harness Boot Cover. The Boot cover will be modified, using a knife cut an "X" shaped cut across the small hole at the top. This cut will be cu

2. Remove Filler Cap. Remove Filler cap only when ready to fill hydraulic Tank with Oil. Do Not leave the Cap off and the system Open, always keep system closed when possible. Avoid any oil contamination. (See Figure 29) 3. Avoid Hydraulic Contamination by filtering the Hydraulic Oil while filling the Hydraulic Tank. Filter bug- gies or carts are commercially available for Hydraulic system cleanup and Oil transfer. These consist of high capacity filter, a Circulating Pump, a Drive Motor and hose

Alamo Group is not responsible for modifications to the MountKit to accommodate these differences. ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas 78155 210-379-1480 © 2005 Alamo Group Inc. TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment