Login:

Festool G9962Z

heruntergeladen wurde: 1Dateigröße: 10 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

Improper oscillation. To check the sanding belt oscillation: 1. Be sure the sanding belt is properly installed and the belt tension knob and air supply are ON. 2. Turn ON the sanding belt. —If the belt oscillates without contacting the limit switches, but the oscillation time to the left and right are NOT equal, proceed to Step 7, on Page 31. 3. An adequate stream of air through the air fork gap (Figure 26) is essential for proper oscillation. If the jet of air is weak through the gap, the

Festool H8192

heruntergeladen wurde: 3Dateigröße: 6 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

#TS9703 PRINTED IN CHINA ...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Festool H2933

heruntergeladen wurde: 1Dateigröße: 4 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

Festool H2934

heruntergeladen wurde: 3Dateigröße: 4 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

Festool H3140

heruntergeladen wurde: 0Dateigröße: 4 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

this may pull the operator’s hand into the machine and cause serious injury! fEEDiNg STOcK. Firmly grasp the workpiece in both hands and ease it into the machine against the direction of rotation using light pressure. do not jam the workpiece into the machine during operation. never sand more than one piece of stock at a time. 6. 7. 8. REpLAciNg SANDiNg BELT. replace sanding belt when it becomes worn. a worn sanding belt can break apart during use, causing personal injury or damage to the machin

Festool H7760

heruntergeladen wurde: 0Dateigröße: 4 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

#JK7691 PRINTED IN CHINA Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or to order new labels. Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readabi

Festool LEX 2 150/7

heruntergeladen wurde: 5Dateigröße: 3 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

Youcan then remove the collar from the snap-onFestool Limited Warrantyfastener (5.2) and replace it with a new one. This warranty is valid on the pre-condition that the tool is used and operated in compliance withthese Festool operating instructions. Festoolwarrants, only to the original consumerpurchaser, that the specified tool will be free fromdefects in materials and workmanship for a termof one year from the date of procurement. Festoolmakes no other warranty, express or implied,for Festool

Festool LEX 2 150/3

heruntergeladen wurde: 8Dateigröße: 3 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

LEX 2 185/. Instruction manualEccentric sander Page 2 - 6 IMPORTANT: Read and understand all instructionsbefore using. Guide d.utilisationPonceuse excentrique Page 7 - 11 IMPORTANT: Lire et comprendre toutes lesinstructions avant de demarrer les travaux. Manual de instruccionesLijadora excentrica Pagina 12 - 16 IMPORTANTE: Lea y comprende todas lasinstrucciones antes de usar. 464 111_00 . GENERAL SAFETY RULE. instructions. Failure to follow all instructionsRead and understand al. listed below ma

Festool LEX 2 185/7

heruntergeladen wurde: 1Dateigröße: 3 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

Consisting of a filter, control unit,condensation drain and lubricator, the serviceunit cleans and lubricates the compressed airand keeps it free of condensation. For thios tool, the lubricator should be set sothat a drop is applied to the compressed airapprox. every 7-10 minutes. .arsenic and chromium from chemically-treated lumber.The risk from these exposures varies, dependingon how often you do this type of work. To reduce your exposure to these chemicals: Work in a well ventilated area,and

Festool G9983

heruntergeladen wurde: 4Dateigröße: 3 mb    Hersteller: Festool  
Kategorie: Schleifmaschinen

1. Low voltage. 2. Open circuit in motor or loose connections. 1. Check power line for proper voltage. 2. Inspect all lead connections on motor for loose or open connections. Motor will not start; fuses or circuit breakers blow. 1. Short circuit in line cord or plug. 2. Short circuit in motor or loose connections. 3. Incorrect fuses or circuit breakers in power line. 1. Inspect cord or plug for damaged insulation and shorted wires. 2. Inspect all connections on motor for loose or shorted termina





Kategorien