Warning Thoroughly investigate the layout of your vehicle before drilling or cutting any holes. Take extra precautions when working near tanks, lines, hydraulic lines, and electrical wiring. Don’t mount this system so that the wire connections are unprotected or are subject to pinching or damage from nearby objects. The +12 volt DC power wire must be fused at the battery positive (+) terminal connection. Before making or breaking power connections at this system’s power terminals, disconnect the

Some states do not allow the exclusion or limitation of incidental or consequential damages. In such states, the exclusion or limitations of this Limited Warranty may not apply to you. This Limited Warranty gives you specific legal rights and you may have other rights which vary from state to state. © 2004 Directed Electronics, Inc. T TTa aab bbl lle eeo oof ffC CCo oon nnt tte een nnt tts ss Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Int

Table of Contents Safety Precautions and FCC Statement 5 Congratulations 6 How to Use this Guide 6 Box Contents 7 Unpacking and Setting up your Soloist Battery Installation 8 Front View 9 Rear View 10 Remote Control 11 Docking Cradle Types 12 Before inserting the Stiletto Cradle 13 Inserting Docking Cradle 14 Setting the Clock 15 LCD Contrast Setting 16 Installing the Windowsill Antenna 17 Using your Soloist Switching Soloist On and Off 18 Selecting a Source 18 Volume Control 19 Equalization Set

You can achieve this mono channel by using the left positive (+) speaker connection and the right negative (-) speaker connection. (Refer to the end panel drawing on the next page.) Note: Total bridged impedance of less than 4-ohms may trigger the protection circuitry causing reduced output and may eventually damage your amplifier. B r i d g i n g You can operate each pair of channels in both stereo and mono (3 channel or tri-mode) at the same time by using highpass filters (bass blockers) on th

Relocating various ground connections Whines and pops: If you have a combination of noises, or if one or more of the problems listed above persists despite efforts to stop the problem, the noise may be caused by one or more of the following problems: . Excessively high input level setting on the amplifier . Poor or open shielding, extra long cables or corroded input cables . Bad connections . Bad (or high resistance) system ground . Reversed polarity on audio signal cables . Poor quality source

The battery usage will vary depending on the operating mode. A fully recharged battery has the following typical playback/recording times: . Video Playback/Video Record: can be used for about 3 hours. . Music Playback/Music Record: can be used for about 7 hours. d © 2005 Directed Electronics—all rights reserved 17 Utility CD Included is a Utility CD (to be used on a PC). Insert the supplied CD into your CD-ROM, and the CD will auto-run the Setup program. On your computer screen, you will see the

Push the Navigation button up or down to select a file from list. Press the Navigation button in, to view the file. Press the Navigation button to the right to preview the photo. 5. After a picture is selected and is displayed on the screen it can be rotated if needed by pushing the Navigation button to the right. Each press to the right will rotate the photo and additional 90 degrees. Press the Navigation button in again, the photo will be displayed normally. 6. While viewing the photo in full

The microphone is located at the top of the media player. NOTE: To avoid battery discharge and subsequent loss of recording, it is suggested that the AC adapter be used to power the media player. NOTE: The record quality is set in the Setting—Record/Voice section of the Setting menu. 3. When the REC • button is pressed, the Record LED will stay illuminated and the Start Recording message will display. 3. To stop recording, press REC • button again. You will see the recorded file being saved to t

5. If your SD/MMC card or Memory Stick has video, audio, or photo files in the inserted card, change to appropriate mode, open the Memory Card folder and select the file to play or view. N NNO OOT TTE EE: :: Before inserting or removing the SD/MMC card or Memory Stick, turn the power off to the media player, otherwise files on the media player and the card or stick might be corrupted! N NNO OOT TTE EE: :: If the memory card is removed before the file is stopped or if a file is selected that is c

When pressing to fast-forward or rewind, you will see the display below showing playback status and elapse time. 11. To adjust brightness/volume of the video playback press the “R” button. The brightness/volume adjustment screen will appear. Push the Navigation button left or right to adjust. There are 16 levels of adjustment, set to the desired level. A brightness/volume status bar will display as shown below, it will disappear in a few seconds if no button is pressed. Press the Navigation butt