air-o-convect 6 GN Maximum capacity of 30 kg, the ideal choice for preparing 40 to 60 meals a day. air-o-convect 10 GN 1/1 on neutral or hot cupboard base Maximum capacity of 50 kg, the ideal choice for preparing 60 to 100 meals a day. air-o-convect 10 GN 2/1 on oven support Maximum capacity of 70 kg, the ideal choice for preparing 100 to 140 meals a day. air-o-convect 20 GN 1/1 with trolley Maximum capacity of 100 kg, the ideal choice for preparing 140 to 200 meals a day. air-o-convect 20 GN 2/

Quick and full service restaurants, supermarkets, small hotels and schools To guarantee quality meals throughout the day. Restaurants and hotels, small canteens, schools and banquet events When you need to serve excellent meals to a large number of people in different environments. Large restaurants and schools, canteens, central and high capacity kitchens The perfect solution when you need to prepare hundreds of meals, all day long, guaranteeing perfect service at all times. 4 electrolux air-o-

Model numbers may have the letters: L, M, 2M, or S. HOW TO INSTALL CABINETS: LOW WATER LIGHT: 1. Remove all packing material from inside and When water needs to be added to the pan, the Low outside of cabinet. Water Light will stay on until the pan is refilled. 2. Position cabinet on level floor; install the cabinet interior (pan slides) if not already installed. Use of treated water is recommended for proper operation and 3. Plug power cord into proper wall receptacle. 4. Fill water pan with th

3. Press the SET button to enter the temperature into the control. 4. Press the START button and the display shows the remaining time in the cook/retherm cycle. NOTES: The control will beep after it times down to zero; it will then automatically switch to the HOLD mode. The display will then show the hold setpoint temperature. For HOLD mode, preheat unit to 180°F/82°C for 60 minutes. 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • Ovens Humidi

Oven is in the “TIMED” mode 2. Probe not plugged in 3. Control defective 1. Switch to “PROBE” mode 2. Plug in probe 3. Replace Control will not switch to “COOK” (probe mode) 1. Oven in “TIMED” mode 2. Probe temperature setting lower than probe temperature 3. Probe not plugged in 4. Control defective 1. Switch to “PROBE” mode 2. Set probe temperature to desired temperature 3. Plug in probe 4. Replace No Humidity 1. Water element defective 2. Humidity control 1. Replace 2. Replace NOTE: Vent fans

NOTE: Do NOT change the mode of the controls (probe or timed) while oven is operating in a Cook/Retherm cycle. Oven must be in the HOLD cycle to change the timer or probe operation. 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • Ovens Humidity with Microprocessor Controls FL-2267 Rev. 8 (1/05) Page 6 of 13 OPERATING INSTRUCTIONS, continued HOW TO OPERATE WITH FOOD, continued HOW TO SET HOLD-ONLY MODE: 1. Push power switch to “ON”. 2. Press th

WARRANTY COVERAGE MAY BE AFFECTED WITHOUT PROPER CLEANING. Cleaning Hints: 1. Use the mildest cleaning procedure that will do the job. 2. Always rub in the direction of polish lines to avoid scratching the surface. MAINTENANCE: CABINET 1. Wipe the inside of cabinet after daily use. 2. Leave doors slightly open to fully dry interior. BEFORE cleaning the cabinet: 1. Unplug cord from wall. Allow cabinet to cool. 2. Do NOT hose cabinet with water. 3. Do NOT get water on controls. 4. Do NOT use abras

8 (1/05) Page 1 of 13 INSTALLATION, OPERATION and MAINTENANCE MANUAL for Cres Cor AQUA-TEMP HUMIDITY CONVECTION and RETHERM OVENS with MICROPROCESSOR CONTROLS CO151FWUA12B CO151XWUA5B CO151FPWUA12B RO151FWUA18B CO151HWUA6B RO151FPWUA18B RO151FW1332B 5925 Heisley Road • Mentor, OH 44060-1833 877/CRES COR (273-7267) • 440/350-1100 Fax: 440/350-7267 • Ovens Humidity with Microprocessor Controls FL-2267 Rev. 8 (1/05) Page 2 of 13 TABLE OF CONTENTS SUBJECT PAGE INSTALLATION INSTRUCTIONS OPERATING INS

8 (1/05) Page 10 of 13 REPLACEMENT PARTS: Include all information on nameplate when ordering parts. ITEM DESCRIPTION 1. Switch (On/Off) 2. Microprocessor Control 3. Vent Fan 4. Fan Guard 5. Fuse Fuse Holder 6. Blower Kit 7. Contactor 8. Terminal Block, front 9. Terminal Block, rear 10. Switch, Fan 11. Hi Limit Switch (Pass-thru) Hi Limit Switch 12. Sensor 13. Sensor Bushing 14. Connector, probe Probe 1.5” long Probe 6” long 15. Relay 16. Thermostat, Humidity 17. Knob 18. Pilot Light 19. Receptac

O av8Цloтfpaq 8ioày8i тov фpéoкo aépa |iéoù тшу onwv тou oтo тош |iépoq кal 8îày8i ^v uypaoía ano тov èàAa^o. O фpéaкoq aépaq nspvàsi liéoa ano tov av8Цloтfpa, 6ia^éaou тшу 08pцavтlкwv otoix8íúv, onou кal 08pцaíV8тal пpoтoU épèsi as 8пaфf це ^v тpoфf • H Л8lтoupYía Hold (naA^f кuкЛoфopía aépa) sívai кaтàЛЛçЛç yia œaxapoпЛaoтlкf, apTOnoiía кal apyo |iay8íp8|ia, svw ç кuкЛoфopía тou aépa це u0çXf тaxUтçтa sívai тéЛеla yia 0fai^o ^sa^ov, ^lap^wv rai Лaxavlкшv Ala0çтfpaq soOTspiMfq esp^^aaía^ тpoф