While these settings are loaded, the COMPARE key’s LED blinks and “COMP” appears in the LED DISPLAY. Press the COMPARE key again to return to edit mode and store your changes. 16 To enter SETUP mode, press the SETUP key. In setup mode, you can access the parameters shown below the four EDIT CONTROLs. For more information about SETUP mode, see chapter 3.6. 1. INTRODUCTION VIRTUALIZER PRO DSP2024P To change a parameter’s value, rotate the JOG WHEEL. To increase the value, turn the wheel clockwise.

It’s an allrounder with so many features that you hardly need any other equipment. Use it as a guitar combo to deliver 2 x 60 Watts stereo with internal or external loudspeakers. However you use your V-AMPIRE, you will always profit from its enormous flexibility. So enough talk: Nothing will convince you more than what you actually hear and feel when you play your V-AMPIRE. But ... 1.1 ... before you get started Your V-AMPIRE was carefully packed at the assembly plant to assure secure trans

'y16 «Hz1« “kHz“" LOW CUT HIGH CUT MASTER ■8 dB +9 MONO WBE GAIN STEREO IMAGE I i №111111111 qc f| a | I №111111111 s HL 7 5 i i z d § 5 ffl' I ilü fl I 1111 811 11II111111 i i itti j i i i INI I rfriT lllll um III I ITTI I I „ .. IIIII I 11 I I ITT l J I I I I ¡8 _jdtk _ . I I I I ITTI J I I :.......gl, ¡iiii i um i J I I I uTTTTTT : n ITT 111111 S J* • p__. „ TTT U I I I I I I S L ,|. ' I I ITTU I I I I ’ .....Trijll 8 .......ffrr '........flr § ll I II II I LL rnr

(42) Use the TALK TO AUX 1/2 switch to activate the built-in talk- back microphone. Its signal is sent to the AUX SEND jacks 1 and 2. Keep the switch pressed while you’re speaking. (43) This is the built-in talkback microphone. 2.6.2 Phones & control room Fig. 2.18: Phones/control room section (44) The PHONES/CTRL R control adjusts the volume of the headphones connected to the PHONES/CTRL ROOM OUT jack (see (46)). If you have an active monitor speaker or power amp connected here, you can also co

So, aux send buses are not the best solution here. Instead, dynamic processors and equalizers are inserted into the signal path. Once processed, the signal then re-enters the mixing console at the same point where it left. Signal interruption only occurs if a plug is inserted into the corresponding jack (1/4" stereo plug: tip = signal output, ring = input). All mono input channels are equipped with insert points. They can also be used as pre-EQ direct outputs, without signal flow interruption. F

EURODESK Overview.................................................6 3. Input/Output Channel................................................6 4. Inserts..........................................................................8 5. Subgroup and Direct Outputs...................................9 6. Master Panel.............................................................10 7. Connections...............................................................13 8. The Patchfield..............................

The pre-fader signals (monitor buses) remain operative. When MUTE is pressed, the corresponding control LED illuminates. m The channel fader controls the channel signal level in the main mix. 2.1.1 Input section [181 Each mono input channel is equipped with a balanced microphone input (XLR connector) which provides +48 V phantom power for condenser microphones at the touch of a button (see rear panel). PMX1000: The two stereo channels 5/6 and 7/8 have an additional balanced XLR microphone in

Plus, our tried and tested “Invisible” Mic Preamps give you crystal-clear audio free of noise and distortion when using microphones. The mixing consoles of the PMX series feature a state of the art, integrated switch-mode power supply (SMPS). One of the great advantages is that (compared to conventional circuits) a switch-mode power supply adapts to mains voltages between 100 and 240 volts automatically. Furthermore, due to its much greater efficiency, it consumes much less energy than a conven

The task to design the new PMX series certainly meant a great deal of responsibility, which we assumed by focusing on you, the discerning user and musician. It also meant a lot of work and night shifts to accomplish this goal. But it was fun, too. Developing a product usually brings a lot of people together, and what a great feeling it is when everybody who participated in such a project can be proud of what we’ve achieved. It is our philosophy to share our joy with you, because you are the mos

Manufactured under IS09000 certified management system 3 EUROPOWER EP15QQ/EP25QQ FOREWORD Dear Customer, welcome to the team of BEHRINGER users, and thank you very much for expressing your confidence in us by purchasing this power amplifier. Writing this foreword for you gives me great pleasure, because it represents the culmination of many months of hard work delivered by our engineering team to achieve a very ambitious goal: to develop two outstanding power amplifiers, whose flexibility