THIS MANUAL CONTAINS IMPORTANT OPERATION, MAINTENANCE AND PRECAUTIONARY INFORMATION. PLEASE PRESENT THIS MANUAL TO USER/OPERATOR/OWNER AFTER INSTALLATION. IT IS STRONGLY ENCOURAGED THAT YOU READ THIS MANUAL BEFORE INSTALLING SYSTEM TO ENSURE THE BEST POSSIBLE INSTALLATION. INSTALLATION MUST CONFORM TO ALL LOCAL AND STATE PLUMBING CODESAND REGULATIONS. CONNECT SYSTEM TO COLD WATER SUPPLY ONLY. WATER TEMP. CAN NOT EXCEED 100°F/28°C. SYSTEM MUST BE INSTALLED IN A VERTICAL AND UPRIGHT POSITION. A

Limit your use of steam to 10 -15 minutes until you are certain of your body’s reaction. d. Excessive temperatures have a high potential for causing fetal damage during the early months of pregnancy. Pregnant or possibly pregnant women should consult a physician regarding correct exposure. e. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a steambath. f. Persons using medic

1. Check that the sensor cable is connected to J4 on the PCA printed circuit assembly. 2. Check the cable connection to the temperature sensor. 3. Replace sensor and/or cable -call AMEREC's Service Department. Control "ON". K60 Control displays "E002". Temperature sensor. or cable shorted. 1. Check sensor cable for damage from nail/staple puncture. 2. Check sensor cable ends for frayed/exposed wire strands. 3. Replace sensor and/or cable -call AMEREC's Service Department. Control "ON". K60 Contr

or Generator is faulty. 1. Replace control -call AMEREC's Service Department. 2. Replace PCA -call AMEREC's Service Department. Sudden increases in rate water sputters out of steam head. Foaming contaminants in the water supply. 1. Flush tank 3 times. See Section 4. 4209-24 12/09/02 4209-24 12-09-02 AK Series w/K60 Control Owners Manual page 4 1 28 12 4 43 29 15 24 23 2 16 7 8 22 19 5 18 17 20 14 6 13 3 39 33 44 21 34 9 36 35 11 P.O. Box 2258, Woodinville WA 98072 425-951-1120 Fax: 425-951-1130

Stay at least 12 inches away from the hot steam escaping from the steam head. Be careful when entering a steambath. Escaping steam from an overheated steam room may cause injury. AK Series w/K60 Control Owners Manual page 2 SECTION 1A: STEAM GENERATOR OVERVIEW The standard K60 model steam generator control the steam room and an optional secondary steam'' feature automatically engages cutting features an adjustable 60 minute time and tem-control is available to mount in an alternate steam product

The 5. To change the preset temperature setting control will alternately display time remaining press and hold the TEMP button on the control. and the actual temperature at the sensor in your While continuing to hold the button, the tempera- steam room every 5 seconds. ture display will increase in 1 degree increments SECTION 3: TAKING A STEAMBATH 1. Wait for the steam room to reach a comfortable temperature. 2. Remove clothing and jewelry. 3. Enter the steam room and close the door to prevent s

The floor protection in front of the stove must extend at least to 100mm beyond both side of the oven mouth and to 400mm In front of jt 3 INSTALLING THE STOVE Figi As in all our stoves, there Is an escape hole for the smoke flue on top of the stove as well as behind it. You can close the unnecessary hole using the |r^ closing trap supplied. Included with the delivery, you will also receive a 2,00mm connecting pipe for connecting the stove to the smoke flue through the back hole. When connect

If the distance is less than 1200mm, you can choose one of the protection methods mentioned in items 1-3. The ceiling protection must extend above the vertical surfaces of the stove. (Figure 6) Figure 6 No protection for the ceiling Single light protection F nr>m Tzoa 000 FIREPLACE BASE The fireplace must be installed on a rigid base. This base must be strong enough to bear the weight of the fireplace and to prevent any excessive rise of temperature of the structural elements connected to

This kind of single light protection can be constructed either by using a minimum 3 inches thick incombustible cement plate reinforced with fiber, or by fastening an at least 20 gauge sheet metal plate densely enough to the wall. A minimum 1-1/4" space must be left between the protective plate and the wooden surface to be protedted. This can be done by using spacers as intermediate supports (Figure 2) I7ÏÏÏ1 3. The safety distance mentioned on item 1 can be further decreased to minimum 5 inche

This kind of single light protection can be constructed either by using a minimum 3 inches thick incombustible cement plate reinforced with fiber, or by fastening an at least 20 gauge sheet metal plate densely enough to the wall. A minimum 1-1/4" space must be left between the protective plate and the wooden surface to be protedted. This can be done by using spacers as intermediate supports (Figure 2) I7ÏÏÏ1 3. The safety distance mentioned on item 1 can be further decreased to minimum 5 inche