. (See Figure B.) 3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure B.) THIS PRODUCT USES A 3-PRONG ELECTRICAL PLUG 120 VOLT, GROUNDED, ELECTRICAL OUTLET FIGURE B DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which sati

7. Do not abuse the Power Cord. Never use the Power Cord to carry the tool or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. Replace damaged Power Cords immediately. Damaged Power Cords increase the risk of electric shock. PERSONAL SAFETY 8. Stay alert. Watch what you are doing, and use common sense when operating this product. Do not use the Fountain while tired or under the influence of drugs, alcohol, or medication. A moment of inattention

If you are using the tool outdoors, use an extension cord rated for outdoor use. (signified by “WA” on the jacket). Note: Do not make the extension cord connection underwater. 17. Do not pump hazardous materials. Do not pump explosive or flammable materials such as Fuel Oil, Kerosene, Gasoline etc. Do not pump in close proximity to flammable or explosive materials. Do not pump fats, oils, salt or waste water. This Pump is designed to move clean or dirty water. Do not pump hot liquid. 18. Water t

2. Use the Compression Tester only in well ventilated areas. A running gasoline engine produces carbon monoxide. Carbon monoxide WARNING! fumes are a colorless, odorless, gas that, if inhaled, can cause serious injury or death. 3. Maintain labels and nameplates on the Compression Tester. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 4. Prior to using the Compression Tester, make sure to read and understand all warnings, safety precau

Many accidents are caused by poorly maintained tools. Use only accessories that are recommended by the manufacturer for your 6. model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE Tool service must be performed only by qualified repair personnel. 1. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow instruc2. tions in the “Inspectio

(See Figure G.) 4. Make sure the ON/OFF Switch (86) is in its “OFF” (down) position. (See Figure G.) 5. Plug the Power Cord Plug (64) of the Air Compressor into the nearest 120 volt, grounded, electrical outlet. 6. Pull up on the ON/OFF Knob (86) to turn on the Air Compressor. (See Figure G.) 7. While the Air Compressor is running, allow sufficient time for the Tank Pressure Gauge (65) to reach at least 85 PSI before using the Compressor. (See Figure G.) 8. Once the Tank Pressure Gauge (65) reac

Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 18. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified techni

note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 1. Choose a mounting location that is free of electrical wiring or other obstructions, and is sturdy enough to support the weight of the Reel and hose as well as the force used to extend and retract it. Purchase four bolts able to support the same forces. 2. Make a paper template from the mounting plate of the Reel. Mark the center of the bolt holes in th

Look for air bubbles. ** To clean the compressor surface, wipe with a damp cloth, using a mild detergent or mild solvent. Every 6 months or 100 Operation Hours: Replace Pump oil.*** Changing the Oil Check the oil periodically for clarity. Replace oil if it appears milky or if debris is present, or every 6 months, or 100 hours of runtime, whichever comes first. WARNING: Risk of personal injury hazard. Allow Air Compressor to cool before changing the oil. To drain the oil from the Pump Crankcase:

It will do the job better and more safely at the rate for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not intended. 21. To extend the life of your air tools and equipment: It is recommended to install a water filter and oiler (available from Harbor Freight Tools) in series with the Air Outlet Valve (part #69) of the Air Compressor. (See Figure C, next page.) SKU 90234 PAGE 8 22. 22. WARNING! People with pacemakers should consult t