Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
7. Do not abuse the Power Cord. Never use the Power Cord to carry the tool or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. Replace damaged Power Cords immediately. Damaged Power Cords increase the risk of electric shock. PERSONAL SAFETY 8. Stay alert. Watch what you are doing, and use common sense when operating this product. Do not use the Fountain while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating this product may result in serious personal injury. 9. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 10. Use safety equipment. Wear ANSI approved safety impact goggles when assembling this product. Non-skid safety shoes must be used for appropriate conditions. TOOL USE AND CARE 11. Disconnect the Power Cord Plug from the power source before making any adjustments, changing accessories, or storing the Pump. Such preventive safety measures reduce the risk of starting the unit accidentally. 12. Store idle equipment out of reach of children and other untrained persons. Electrically powered products are dangerous in the hands of untrained users. 13. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect this product’s operation. If damaged, have the Fountain serviced before using. Many accidents are caused by poorly maintained equipment. SERVICE 14. Service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 15. When servicing this product, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Pump. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Wear ANSI approved safety impact eye goggles when assembling the Pump. Using personal safety devices reduce the risk for injury. Safety impact eye goggles are available from Harbor Freight Tools. 3. Use the right product for the job. There are certain applications for which this product was designed. Do not use small tools, attachments, or equipment to do the work of larger industrial tools, attachments, or equipment. 4. Maintain a safe environment. Keep the area well lit. Make sure there is adequate surrounding space. Always keep the area free of obstructions, grease, oil, trash, and other debris. Do not use an electrically powered product in areas near flammable chemicals, dusts, and vapors. 5. WARNING! Risk of electrical shock. Always disconnect the Pump from its power source before handling or making any adjustments to the tool. Always wear non-skid rubber boots when water is on the floor and you must unplug the Pump. Never allow the internal Motor to get wet. Make sure the electrical power source is a separately fused, grounded, 3-wire type GFCI (Ground Fault Circuit Interrupter) outlet. Do not remove the ground prong on the Power Cord Plug. Do not use an extension cord. 6. Do not pump hazardous materials. Do not pump explosive or flammable materials such as fuel, oil, kerosene, gasoline, etc. Do not pump in close proximity to flammable or explosive materials. Do not pump fats, oils, salt or waste water. This Pump is designed to move clean or dirty water only. Do not pump water over 95 degrees Fahrenheit. 7. Make sure the discharge pipe (not included) is secured to a solid surface to ensure the stability of the Pump. 8. Make sure to position the Pump on a flat, level, solid surface. 9. WARNING! Always arrange a “drip loop” in the Power Cord connecting the Pump to a 120 volt, GFCI electrical outlet. A drip loop is that part of the Power Cord below the level of the outlet to prevent water from traveling along the Power Cord and coming in contact with the outlet. If the Power Plug or electrical outlet does get wet, do not unplug the Power Cord. Disconnect the fuse or circuit breaker that supplies power to the Pump. Then, unplug the Power Cord and examine for presence of water in the outlet. (See Figure A.) Drip Loop OUTLET PUMP DEVICE OUTLET FIGURE A CORD 10. If necessary, have a certified electrician install (within 14 feet of where the Pump will be located) a 120 volt, GFCI electrical outlet that is dedicated only to the Pump. Any outlet should be above the water line. 11. NEVER raise or lower the Pump by its electrical Power Cord. 12. In cold weather, when the Pump is not in use, protect the interior of the Pump from freezing by draining the water and pumping a permanent type automobile anti-freeze containing a rust inhibitor through the syste...
Dieses Handbuch ist für folgende Modelle:Pumps - SUBMERSIBLE DIRTY WATER PUMP 93820 (646.71 kb)