Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
It will do the job better and more safely at the rate for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not intended. 21. To extend the life of your air tools and equipment: It is recommended to install a water filter and oiler (available from Harbor Freight Tools) in series with the Air Outlet Valve (part #69) of the Air Compressor. (See Figure C, next page.) SKU 90234 PAGE 8 22. 22. WARNING! People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. 23. WARNING! The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. TO AIR TOOL WATER FILTER OILER AIR OUTLET VALVE (#69) FIGURE C UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on pages 14 and 15 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts mentioned in the following pages, refer to the Assembly Diagram on page 16. 1. IMPORTANT! Always fill the Air Compressor with a premium quality, SKU 90234 PAGE 9 30-weight, non-detergent, compressor oil before each use. Running the Air Compressor with no oil or low oil will cause damage to the equipment and void the warranty. To check the level of oil, make sure the Air Compressor is 30-weight, non-detergent, compressor oil before each use. Running the Air Compressor with no oil or low oil will cause damage to the equipment and void the warranty. To check the level of oil, make sure the Air Compressor is . Then, observe the Oil Level Window (part #72). The level of oil should just reach the horizontal line as shown on the Oil Level Window. If the level of oil is below the horizontal line, remove the Oil Plug (part #78) and add new oil through the Oil Plug hole. Make sure not to overfill. The Air Compressor is designed to hold approximately 25 fluid ounces of oil. Then screw in the Oil Plug, being careful not to strip the threads. (See Figure D.) OIL PLUG (#78) OIL LEVEL WINDOW (#72) PRESSURE RELIEF VALVE (#67) FIGURE D 2. Turn the Air Outlet Valve (part #69) to its CLOSED position. Then connect a high pressure air hose (not included) equipped with a quick connectorto the Air Outlet Valve. If using a water filter and oiler in series with the Air Outlet Valve of the Air Compressor, connect the other end of the air hose to the water filter and oiler and connect the water filter and oiler to the air tool being used. If not using a water filter and oiler, squirt several drops of air tool oil into the air intake plug of the air tool. Then, connect the other end of the air hose directly from the Air Outlet Valve of the Air Compressor to the air tool. (See Figure E, and Figure F, next page.) AIR OUTLET VALVE (#69) CONNECT AIR HOSE HERE. CLOSED POSITION OPEN POSITION FIGURE E SKU 90234 PAGE 10 REV 04/04 3. Make sure the Tank Drain Valve (part #59) is closed. (See Figure F.) 4. Make sure the “On/Off” Pressure Switch (part #66) is DOWN in its OFF position. Then, plug the Power Cord (part #64) into the nearest 120 volt, grounded, electrical outlet. (See Figure F.) 5. Pull UP on the “On/Off” Pressure Switch (part #66) to its ON position. (See Figure F.) AIR OUTLET VALVE (#69) AIR HOSE (NOT INCLUDED) ATTACH TO AIR TOOL. TANK DRAIN VALVE (#59) AIR OUTLET PRESSURE GAUGE (#71) TANK PRESSURE GAUGE (#65) PRESSURE REGULATOR (#70) PRESSURE SWITCH (#66) FIGURE F “ON/OFF” 6. Allow the Air Compressor to build up from 85 PSI to 115 PSI as indicated on the Tank Pressure Gauge (part #65). When the air pressure reaches 85 PSI, open the Air Outlet Valve (part #69) to allow the air hose and air tool to become pressurized. (See Figure F.) 7. As long as the “On/Off” Pressure Switch (part #66) is in its ON position the operation of the Air Compressor is automatic, controlled by an internal pressure switch. The Air Compressor will turn on automatically when the air pressure drops to 85 PSI as indicated on the Tank Pressure Gauge (part #65), and will turn off automatically when the air pressure reaches 115 PSI as indicated. IMPORTANT: The internal pressure switch is adjustable, but changes to the air pressure levels should not be done. Any change to the automatic pressure levels will cause additional stress on the motor which may result in shortened motor life and will void the warranty. (See Figure F.) SKU 90234 PAGE 11 8. Turn the Pressure Regulator (part #70) counterclockwiseto increase the amount of compressed air to the air tool being used (from 90 PSI to 115 PSI). Turn the Pressure Regulator cloc...