Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 1. Choose a mounting location that is free of electrical wiring or other obstructions, and is sturdy enough to support the weight of the Reel and hose as well as the force used to extend and retract it. Purchase four bolts able to support the same forces. 2. Make a paper template from the mounting plate of the Reel. Mark the center of the bolt holes in the desired mounting location. 3. Check for hidden wiring, then, drill holes to accommodate the bolts (not included). 4. Mount the Reel and secure in place with four bolts. 5. Align the holes of the Handle with the holes on the Reel Flange and secure the Handle in place with the three Screws, Nuts and Washers. SaFetY OPeRatiOn maintenanCeSetuP Page 5For technical questions, please call 1-800-444-3353.Item 40131 Operating instructions Read the entiRe imPORtant SaFetY inFORmatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. inspect tool before use, looking for damaged, loose, and missing parts. if any problems are found, do not use tool until repaired. General Operating instructions 1. Attach a coupler (sold separately) to your air compressor hose and apply thread seal tape to the Inlet fitting on the Reel. Connect the coupler to the Inlet fitting. 2. Connect your air tool to the other end of the Hose using another coupler and thread seal tape. 3. Follow all instructions from the air tool and compressor for set up and use. 4. When finished using the Hose, disconnect the air tool and wind the hose. Wipe the Hose Reel clean with a dry cloth. SaFetYOPeRatiOnmaintenanCe SetuP Operating instructions Read the entiRe imPORtant SaFetY inFORmatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. inspect tool before use, looking for damaged, loose, and missing parts. if any problems are found, do not use tool until repaired. General Operating instructions 1. Attach a coupler (sold separately) to your air compressor hose and apply thread seal tape to the Inlet fitting on the Reel. Connect the coupler to the Inlet fitting. 2. Connect your air tool to the other end of the Hose using another coupler and thread seal tape. 3. Follow all instructions from the air tool and compressor for set up and use. 4. When finished using the Hose, disconnect the air tool and wind the hose. Wipe the Hose Reel clean with a dry cloth. SaFetYOPeRatiOnmaintenanCe SetuP Page 6 For technical questions, please call 1-800-444-3353. Item 40131 user-maintenance instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. tO PRevent SeRiOuS injuRY: Detach air supply from this product before performing any inspection, maintenance, or cleaning procedures. tO PRevent SeRiOuS injuRY FROm tOOl FailuRe: Do not use damaged equipment. if abnormal noise, vibration, or leaking air occurs, have the problem corrected before further use. Cleaning, maintenance, and lubrication note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the Hose Reel. 1. BeFORe eaCh uSe, inspect the general condition of the tool. Check for: • loose hardware or housing, • misalignment or binding of moving parts, • cracked or broken parts, and • any other condition that may affect its safe operation. 2. aFteR eaCh uSe, re-wind the hose onto the reel and wipe the Hose Reel clean with a dry cloth. SaFetY OPeRatiOn maintenanCeSetuP user-maintenance instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. tO PRevent SeRiOuS injuRY: Detach air supply from this product before performing any inspection, maintenance, or cleaning procedures. tO PRevent SeRiOuS injuRY FROm tOOl FailuRe: Do not use damaged equipment. if abnormal noise, vibration, or leaking air occurs, have the problem corrected before further use. Cleaning, maintenance, and lubrication note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the Hose Reel. 1. BeFORe eaCh uSe, inspect the general condition of the tool. Check for: • loose hardware or housing, • misalignment or binding of moving parts, • cracked or broken parts, and • any other condition that may affect its safe operation. 2. aFteR eaCh uSe, re-wind the hose onto the reel and wipe the Hose Reel clean with a dry cloth. SaFetY OPeRatiOn maintenanCeSetuP Item 40131 For technical questions, please call 1-800-444-3353. Page 7 Part Description Qty 1 Base 1 2 Stand 1 3 Fixed Washer 1 4 Washer 1 5 Position Sleeve 1 6 Flange A 1 7 Sleeve 1 8 Flange B 1 9 Position Sleeve 1 10 Washer 1 11 Spring 1 12 Washer 1 13 Swivel (2 valves & O-rings) 1 Part Description Qty 14 Spring Washer 1 15 Nut 3 16 Washe...