Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 18. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. 19. Use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. This tool requires use of an extension cord of 0 to 10 amps capability (up to 50 feet), with wire size rated at 18 AWG. Longer extension cords require larger size wire. If you are using the tool outdoors, use an extension cord rated for outdoor use (signified by “WA” on the jacket). 20. Pacemaker safety warning. People with pacemakers should consult with their physician(s) before using this product; operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. 21. Drain compressor every day. Do not allow moisture to build up inside the compressor. Do not allow compressor to sit pressurized for longer than one hour. 22. Make sure all equipment is rated to the appropriate capacity. Adjust the output air pressure to the tool’s operating capacity. 23. Avoid explosions and fire. Never place flammable objects near the compressor. Never spray water or any flammable liquids towards the compressor. 24. Avoid body injury. Never direct the air outlet at persons or animals. 25. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) Note: Performance of this tool may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the following parts are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Water Spill Valve Blow gun with tipTire chuckOn/Off Switch REV 09/06 Assembly 1. Attach the Coil Air Hose to the Air Outlet as shown below. 2. Regulator Pressure Gauge I (46)Regulator Pressure Gauge II (50) Coil Air HoseRegulator Adjusting Knob (53) Pressure Release ValveAttach the Blow Gun (with desired tip), tire chuck, or other user supplied attachment to the other end of the Coil Air Hose. Operation Turning Compressor On 1. Plug the power cord into an electrical outlet with a grounding prong. Note: Only use a 115V electrical source (± 10% maximum variation.) 2. Push the On/Off Switch to the ON position. 3. Allow the Tank to fill to 80 PSI before using. With the Air Compressor turned on, operation is automatic and under the control of the internal pressure switch. Internal Pressure Switch Caution: Do not make changes to the internal pressure level switch; any change to the automatic On/Off pressure levels will cause additional stress on the motor which may result in shortened motor life. Doing so will void the warranty. Using the Pressure Relief Valve The Pressure Relief Valve is used when decompression is needed quickly and efficiently. 1. Press the On/Off Switch to the OFF position. 2. Pull on the Pressure Release Valve ring to release pressure. Caution: Wear safety glasses. The released air is under high pressure and can cause debris and dirt to fly as the air exits the tank. REV 11/04 Empty Air and Condensation The water spill valve Petcock (11) is located underneath the Air Tank (shown in the photo on page 4). It must be used daily to release all trapped moisture from the tank. It will also get rid of any condensation that may cause tank corrosion. Warning: Do not open the Water Spill Valve so that more than four threads are showing. 1. Push the On/Off Switch to turn the compressor off. 2. Unscrew the water spill valve Petcock (11) two to three turns only. 3. When all pressure is released, close the water spill valve again. Maintenance 1. Purge the Air Tank daily of all air and moisture to prevent corrosion. 2. Store the Air Compressor in a clean and dry location. 3. Check all air fittings for leaks before using. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. N...