The grounding wire has insulation with an outer surface that is green - with or without yellow stripes. If these grounding instructions are not completely understood, or if in doubt as to whether the compres sor is properly grounded, have the installation checked by a qualified electrician. 120 Volts, 15 Amps 120 Volt Models Air Hose The air hose attached to your compressor has an integral pressure adjusting valve at the working end of the hose. Should service or replacement be required, make su

2. Increase frequency of oil changes if humidity or operating conditions are extreme. Every 160 Hours of Operation: 1. Check drive belt tension; adjust if necessary. (Refer to SERVICE INSTRUCTIONS in this manual.) 2. Inspect air lines and fittings for leaks; correct as necessary. 3. Check the alignment of the motor pulley to the flywheel. If necessary, align to within 1/32 inch on centerline. Each Year of Operation or if a Problem is Suspected: Check condition of air compressor pump intake and e

The pressure adjusting valve can be used to set approximate pressure between 10 and 125 P.S.I. (125 P.S.I. is the highest pressure this compressor will deliver). It is normal for the adjustable pressure valve to release air during operation. ALWAYS SET THE PRESSURE VALVE AT OR BELOW THE REQUIRED PRESSURE FOR THE ACCESSORY BEING USED BEFORE STARTING YOUR COMPRESSOR. FOR INFLATION OR OTHER USES REQUIRING ACCURATE PRESSURE, USE A PRESSURE GAUGE. INSTALLATION AND BREAK-IN PROCEDURES Location of the

• The overloads must be configured for manual reset. • Normal full load run current for each Compressor on the module at 4800 rpm (80 Hz) is approximately 23A. • The customer control circuit must supply an Enable signal to the VFD before the drive will accept a Run Fwd signal. • The VFD will start when the Enable signal is on and a Run Fwd signal is applied. • The VFD will stop if the Run Fwd signal is off or the Enable signal is removed. NOTE The drive provides 24V for the Enable and Run Fwd si

• The valve is a back pressure regulator which can maintain a steady discharge pressure, however the majority of packages with our modules are controlled through suction gas recycle. Also, most packages have a back pressure regulator on the discharge of our modules to control the actual discharge pressure to a minimum of 70 PSIG. • The presence of the valve was thought to protect the end user in case the discharge of our module is isolated from the skid-level pressure relief valve and the other

WARNING The Compressor Module must be installed ONLY in systems that have been designed by qualified engineering personnel. The system must conform to all applicable local and national regulations and safety standards. These instructions are intended to assist in the installation and operation of the Compressor Module and MUST be kept with the Compressor. Service and maintenance of the Compressor Module must be performed by qualified technicians only. Service and maintenance must conform to all

4.5.1 Topping Off the Oil Level See 4.4 - Oil Capacity and Type on page 19 before adding oil. Also refer to 4.2 - Maintenance Tools on page 18 for information about the tools used in this procedure. Note Adding oil through the Schrader valve on either compressor suction fitting permits adding the oil with the compressor running. Adding Oil 1. Turn the knob on the backseating control valve fully counterclockwise. 2. Remove the protective cap from the Schrader valve on either compressor suction fi

ALWAYS refer to the coating material suppliers instructions and COSHH sheets before using this equipment. Users must comply with all local and national codes of practice and insurance company requirements governing ventilation, fire precautions, operation and house-keeping of working areas. This equipment, as supplied, is NOT suitable for use with Halogenated Hydrocarbons. Static Electricity can be generated by fluid and/or air passing through hoses, by the spraying process and by cleaning non-

ANY ELECTRICAL WIRING OR REPAIRS REQUIRE ON THIS PRODUCT SHOULD BE PERFORMED BY AUTHORIZED SERVICE CENTER PERSONNEL IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES. MAKE CERTAIN THAT THE ELECTRICAL CIRCUIT TO WHICH THE COMPRESSOR IS CONNECTED PROVIDES PROPER ELECTRICAL GROUNDING, CORRECT VOLTAGE AND ADEQUATE FUSE PROTECTION. CONTINUE NEXT PAGE . 4 — ENG HAZARD WHAT CAN HAPPEN HOW TO PREVENT IT RISK FROM YOUR AIR COMPRESSOR IS POWERED BY ALWAYS WEAR ANSI Z87.1 APPROVED FLYING OBJECTS THE C

(Refer to Service Instructions in this manual.) 2. Inspect air lines and fittings for leaks; correct as necessary. 3. Check the alignment of the motor pulley to the fly wheel. If necessary, align to within 1/32 inch on centerline. Every 300 Hours of Operation 1. Drain and refill compressor crankcase with clean oil. Refer to Service Instructions for recommended oils. 2. Increase frequency of oil changes if humidity or operating conditions are extreme. Each Year of Operation (2000 Hours or if a Pr