921.153120 ® CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions. • Safety Instructions • Installation & Operation • Maintenance & Storage • Troubleshooting Guide • Parts List • Espanol, p. 10 Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 08/11/2006 Part No. E102346 Table of Contents Page Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Bel

Quick Connect Offers a quick attaching and release feature for removing the air hose. Regulator The air pressure coming from the air tank is controlled by the regulator, To increase the pressure, turn the knob clockwise and to decrease the pressure turn the knob counterclockwise, @ Oil Fill Cap Tank Safety Valve Used to allow excess tank pressure to escape valve should only open when the tank pressure is above the maximum rated pressure. Sight Gauge Tube Pressure Switch This controls the power t

If the safety valve does not allow air to be released when you pull out on the ring, or does not close automatically, it must be replaced. Items to Check/Change Check Tank Safety Valve Before each or daily X use Overall Unit Visual Check X Drain Tank X Check Power Cord for Damage X To ensure efficient operation and longer life of the air compressor unit, a routine maintenance schedule should be followed. The following schedule is geared toward a consumer whose compressor is used in a normal work

HAZArD risk FrOM NOise WHAT CAN HAPPeN HOW TO PreveNT iT • Under some conditions and dura• Always wear certified safety equiption of use, noise from this product ment: ANSI S12.6 (S3.19) hearing may contribute to hearing loss. protection. SAVE THESE INSTRUCTIONS FOR FUTURE USE N014212 8 - ENG GLOSSARYGLOSSARY Become familiar with these terms before operating the unit. CFM: Cubic feet per minute. SCFM: Standard cubic feet per minute; a unit of measure of air delivery. PSIG: Pounds per square inch

(1) The model number which can be found on the tabel on the rear of the air tank. (2) The code number which can be found on the foil tabel on the rear of the air tank. (3) The Manufacturers Number (MFG.,.) {ASME Code Compressors onty) is located on the metst date plate which is welded onto the backside of the air tank. (This data plate is painted the same cotor as the tank.) (4) The Motor Manufacturers name which is mocated on the motor tabel or specification plate. (5) The Motor Mfg. number-ats

Install the regulator on the end of the manifold using the short pipe hippie. The arrow on the bottom of the regulator must point away from the manifold in order for the regulator to function properly'. Next, install the gauge, adapter and plug in the regulator. The ptug is supplied with the regulator. BREAK= N PROCEDURES ° the minimum wire size is t2 gauge (AWG}. Sears #9 83606, 12 gauge x 50' extension cord is available at your local Sears Service Center. (Wire size increases as gauge number d

The exhaust valve remains closed. On the upstroke of the piston, air is compressed. The intake valves close and compressed air is forced out through the exhaust valve, through the outlet tube, through the check vatve and into the air tank. Working air is not available until the compressor has raised air tank pressure above that required at the air outlet. Check Vatve: When the air compressor is operating, the check valve is "open", allowing compressed air to enter the air tank. When the air comp

HAZARD WARNING: Risk of explosion or fire What Could Happen How To Prevent It It is normal for electrical contacts within the motor and pressure switch to spark. Always operate the compressor in a well ventilated area free of combustible materials, gasoline, or solvent vapors. If electrical sparks from compressor If spraying flammable materials, locate come into contact with flammable compressor at least 20 feet away from vapors, they may ignite, causing fire or spray area. An additional length

Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet. Drain Valve: The drain valve is located at the base of the air tank and is used to drain condensation at the end of each use. Check Valve: When the air compressor is operating, the check valve is "open", allowing compressed air to enter the air tank. When the air compressor reaches "cutout" pressure, the check valve "closes", allowing air pressure to remain inside the air tan

• Safety Instructions • Installation & Operation • Maintenance & Storage • Troubleshooting Guide • Parts List • EspaSol, p. 10 Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www sears corn 5/2C_2005 Pam NO E101434 TABLE OF CONTENTS Page Warranty ............................................................. See Below Safety Symbols ........................................................... 1 Important Safety Instructions & Guidelines ..................................... 1 Specificatio