Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
HAZArD risk FrOM NOise WHAT CAN HAPPeN HOW TO PreveNT iT • Under some conditions and dura• Always wear certified safety equiption of use, noise from this product ment: ANSI S12.6 (S3.19) hearing may contribute to hearing loss. protection. SAVE THESE INSTRUCTIONS FOR FUTURE USE N014212 8 - ENG GLOSSARYGLOSSARY Become familiar with these terms before operating the unit. CFM: Cubic feet per minute. SCFM: Standard cubic feet per minute; a unit of measure of air delivery. PSIG: Pounds per square inch gauge; a unit of measure of pressure. Code Certification: Products that bear one or more of the following marks: UL, CUL, ETL, CETL, have been evaluated by OSHA certified independent safety laboratories and meet the applicable Underwriters Laboratories Standards for Safety. Cut-In Pressure: While the motor is off, air tank pressure drops as you continue to use your accessory. When the tank pressure drops to a certain low level the motor will restart automatically. The low pressure at which the motor automatically restarts is called "cut-in" pressure. Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a certain high pressure before the motor automatically shuts off, protecting your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called "cut-out" pressure. Branch Circuit: Circuit carrying electricity from electrical panel to outlet. ACCessOries This unit is capable of powering the following accessories. The accessories are available through the current Power and Hand Tool Catalog or full-line Sears stores. Accessories Refer to the selection chart located on • In Line Filter the unit to select the tools this unit is capable of powering. • Tire Air Chuck • Quick Connector Sets The use of any other accessory (various sizes) • Air Pressure Regulators not recommended for use with this tool could be hazardous. Use • Oil Fog Lubricators only accessories rated equal to • Air Hose: 1/4", 3/8" or 1/2" I.D. in or higher than the rating of the air various lengths compressor. DUTY CYCLE This air compressor pump is capable average duty cycle be maintained; of running continuously. However, to that is, the air compressor pump prolong the life of your air compressor, should not run more than 30-45 it is recommended that a 50%-75% minutes in any given hour. 9 - ENG N014212 AsseMBLY AsseMBLY Unpacking 1. Remove unit from carton and discard all packaging. iNsTALLATiON HOW TO SET UP YOUR UNIT Location of the Air Compressor • Locate the air compressor in a clean, dry and well ventilated area. • The air compressor should be located at least 12" (30.5 cm) away from the wall or other obstructions that will interfere with the flow of air. • The air compressor pump and shroud are designed to allow for proper cooling. The ventilation openings on the compressor are necessary to maintain proper operating temperature. Do not place rags or other containers on or near these openings. GROUNDING INSTRUCTIONS Risk of Electrical Shock. In the event of a short circuit, grounding reduces the risk of shock by providing an escape wire for the electric current. This air compressor must be properly grounded. The portable air compressor is equipped with a cord having a grounding wire with an appropriate grounding plug (see following illustrations). 1. The cord set and plug with this unit contains a grounding pin. This plug MUST be used with a grounded outlet. IMPORTANT: The outlet being used must be installed and grounded in accordance with all local codes and ordinances. 2. Make sure the outlet being used has the same configuration as the grounded plug. DO NOT USE AN ADAPTER. See illustration. GroundingPinGroundedOutlets Plug 3. Inspect the plug and cord before each use. Do not use if there are signs of damage. 4. If these grounding instructions are not completely understood, or if in doubt as to whether the compressor is properly grounded, have the installation checked by a qualified electrician. Risk of Electrical Shock. IMPROPER GROUNDING CAN RESULT IN eLeCTriCAL sHOCk. Do not modify the plug provided. If it does not fit the available outlet, a correct outlet should be installed by a qualified electrician. Repairs to the cord set or plug MUST be made by a qualified elec trician. N014212 10 - ENG extension Cords If an extension cord must be used, be sure it is: • a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept the plug on the product • in good condition • no longer than 50 feet • 14 gauge (AWG) or larger. (Wire size increases as gauge number decreases. 12 AWG and 10 AWG may also be used. DO NOT USE 16 OR 18 AWG.) The use of an undersized extension cord will cause voltage to drop resulting in power loss to the motor and overheating. Instead of using an extension cord, increase the working reach of the air hose by attaching another length of hose to its end. Attach additional le...