Call your Graco distributor for information. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. • Do not use hoses to pull equipment. • Comply with all applicable safety regulations. BURN HAZARD Equipment surfaces and fluids that are heated can become very hot during operation. To avoid severe burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely. 311879F Warning Warning TOXIC FLUID OR FUMES HAZARD Toxic fluids or

6. AVOID UNINTENTIONAL STARTING. Do not carry the compressor while it is connected to its power source or when the air tank is filled with compressed air. Be sure the knob of the pressure switch in the “OFF” position before connecting the compressor to its power source. 7. STORE COMPRESSOR PROPERLY. When not in use, the compressor should be stored in indoor dry place. Keep out of reach of children. Lockout the storage area. 8. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. Clear all work

7 APPLICATIONS.................................................................................................................................................... 8 PRIOR TO OPERATION ...................................................................................................................................... 8 TRANSPORT ....................................................................................................................................................... 8 OPERATION .....

See Technical Data, page 20. Flush until clean solvent comes out of hose. 312350E Operation Starting Pump 1. Turn on hydraulic power supply. 2. Open return line shut-off valve (H) first, then slowly open the hydraulic supply shut-off valve (L). 3. Adjust flow control valve (Q) to limit the hydraulic flow to no more than 3 gpm (11 lpm), which is approximately 60 cycles per minute. 4. Adjust pressure reducing valve (N) to increase hydraulic inlet pressure from 50 to 600 psi (0.34 to 4.1 MPa, 3.4 t

Save these instructions. See page 3 for model information, including maximum working pressure. TI8900a TI8885a II 2 G Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Dura-Flo Pumps with NXT™ Air Motors . . . . . . . 3 Dura-Flo Pumps with Viscount® Hydraulic Motors 5 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Grounding . . . . . . . . . . . . . . .

Please keep this manual available for others before they use the compressor. INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS FOR AIR COMPRESSOR MANUEL D’UTILISATION ET CONSIGNES DE SECURITE DU COMPRESSEUR MANUAL DE INSTRUCCIONES Y INSTRUCCIONES DE SEGURIDAD PARA EL COMPRESOR DE AIRE ADVERTENCIA .La utilizacion inadecuada e insegura de este compresor puede resultar en la muerte o en lesiones serias! Este manual contiene informacion importante sobre la seguridad del producto. Antes de utilizar el compr

(10 mm) OD 114478 114478 1 TUBE, flare; sst; 9/16–18 unf–2a x 3/8 in. (10 mm) OD 114477 114477 1 8 FITTING, bulkhead 192889 192889 192889 192889 1 9 WASHER, flat; 9/16 in. 114830 114830 114830 114830 1 10 NUT, hex; 9/16–18 102300 102300 102300 102300 1 11 NIPPLE; cst; 3/8 npt 156849 156849 1 NIPPLE; sst; 3/8 npt 166469 166469 1 12 UNION, swivel, straight; cst; 3/8 npt(m) x 3/8 npsm(f) 155665 155665 1 UNION, swivel, straight; sst; 3/8 npt(m) x 3/8 npsm(f) 235208 235208 1 13 FLUID FILTER; cst; see

Please read and understand this manual before operating the compressor. Please keep this manual available for others before they use the compressor. AVERTISSEMENT Une utilisation du compresseur de maniere incorrecte ou ne respectant pas les consignes de securite peut entrainer la mort ou de graves blessures ! Ce manuel renferme des informations importantes relatives a la securite. Veuillez lire attentivement toutes les instructions avant de mettre le compresseur en service. Laissez ce manuel a l

CAUTION: In order to avoid damaging the compressor, do not allow the unit to be tilted more than 10° when operating. (2) Place this compressor at least 12 inches away from obstacles that may prevent proper ventilation. Do not place this compressor in an area: . where there is evidence of oil or gas leaks. . where flammable gas vapors or materials may be present. . where air temperatures fall below 14°F (–10°C) or exceed 104°F (40°C). . where extremely dirty air or water could be drawn into this