Tighten the screw. Adjust the blade guide bearings (C,G) by loosening the screw (E) and rotating the bearing on the shaft (F) so that the bearings touch, but do not pinch the blade. To gain access the back bearing (G), you will need to remove the table insert and tilt the table to the right. Return table to level position. The front edge of the guide bearings (C) should be just behind the “gullets” of the saw teeth. To adjust, loosen the hex screw (D) and slide the bearing assembly into place. T

REVIEW SAFETY RULES AND OPERATING INSTRUCTIONS FREQUENTLY. This booklet is provided for your convenience: iw the use ami care of your new DeWalt Saw. These instructions include operation, usage, precautions^ preventive maintenance, maintenance and other pertinent data to assist you in assuring long; life and dependable service from your saw. 700 8" RADIAL ARM SAW No. 7700/3400,120 VOLT, TYPE 5 No. 7700-01,220 VOLT, TYPE 5 Bulletin No. 8814 - INDEX Unpacking, Set-Up..............2-4 Macfii

3. When making this adjustment, MAKE SURE THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE and lower the blade as far as possible. Rotate the blade by hand to make certain the teeth do not contact any metal surfaces and adjust if necessary. After adjustment is completed, tighten locknut (A) Fig. 29. A B C Fig. 29 13 1313 ADJUSTING BLADE GUARD After an extended period of time the movable blade guard (A) Fig. 30, might become sloppy and move erratically when the cuttinghead is lowered. This can b

For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). 10" Table Saw (Model 36-600) PART NO. 901608 (014) Copyright © 2001 Delta Machinery ESPANOL: PAGINA 29 To learn more about DELTA MACHINERY visit our website at: For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machine

36-714 36-714 10" Hybrid Saw Scie hybride de 254 mm (10 po) Sierra combinada de 254 mm (10'') Instruction Manual Manuel d’Utilisation Manual de Instrucciones FRANCAIS (27) ESPANOL (53) (800) 223-7278 - US (800) 463-3582 - CANADA A19706_10-05-06 Copyright © 2006 Delta Machinery TABLE OF CONTENTS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ....................2 SAFETY GUIDELINES - DEFINITIONS .....................2 GENERAL SAFETY RULES .......................................3 ADDITIONAL SPECIF

For most work, 3/4” stock is suitable, although an occasional job may require 1” facing. Fig. 64 A 23 CONSTRUCTING A FEATHERBOARD Featherboards are used to keep the work in contact with the fence and table (Fig. 69), and help prevent kickbacks. Dimensions for making a typical featherboard are shown in Fig. 69. Make your featherboard from a straight piece of wood that is free of knots and cracks. Clamp the featherboard to the fence and table so that the leading edge of the featherboard will suppo

24 P C D Fig. 24 P C D Fig. 25 E 14. Hold the blade guard and lower the saw blade. Install the table insert (E) Fig. 25 in the open ing of the saw table. 15. Place a straight edge (B) across the table at both ends of the table insert (Fig. 26). Ensure that the table insert (A) is level with the table. If an adjustment is necessary, turn the adjusting screws (C) with the 1/8" hex wrench. MOTOR COVER NOTE: If your Unisaw uses an LVC Starter Box, attach the two bottom spring clips to the motor cove

The following information describes the safe and proper method for performing the most common sawing operations. This instruction manual does not provide information regarding the installation of a fence system. A fence system must be installed before use of the saw. Please refer to the fence instruction manual regarding the proper installation, alignment, and operation of the fence system. The use of attachments and accessories not recommended be Delta may result in injury. Never operate the sa

Fig. 49 Fig. 50 C When cross-cutting a number of pieces to the same length, clamp a block of wood (B) to the fence and use it as a cutoff gauge (Fig. 51). The block (B) must be at least 3/4" thick to prevent the cut-off piece from binding between the blade and the fence during removal from the saw table. Always position this block of wood in front of the saw blade. Once the cut-off length is determined, lock the fence and use the miter gauge to feed the work into the cut. When using the block (B

Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water. SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 4 ADDITIONAL SPECIFIC SAFETY RULES ADDITIONAL SPECIFIC SAFETY RULES FAILURE TO FOLLOW THESE RULES