Recommended Minimum Wire Gauge for Extension Cords* Nameplate Extension Cord Length Amperes 25' 50' 75' 100' 150' 0 - 2.0 2.1 - 3.4 3.5 - 5.0 5.1 - 7.0 7.1 - 12.0 12.1 - 16.0 16.1 - 20.0 18 18 18 18 16 14 12 18 18 18 16 14 12 10 18 18 16 14 12 10 18 16 14 12 10 16 14 12 12 * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE. 8 Quik-Lok ® Blade Clamp • Periodically clean the Quik-Lok ® Blade Clamp with compressed air.

5). WARNING! To reduce the risk of injury, keep hands away from the blade and other moving parts. Trigger Speed Control Switch The Sawzall® HatchetTM is equipped with a trigger speed control switch. It may be operated at any speed from zero strokes per minute to full speed. Always start tool before blade contacts the workpiece. 1. To start the tool, grasp the handle firmly and pull the trigger. 2. To vary the speed, increase or decrease the pressure on the trigger. The further the trigger is pul

18. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the tool accidentally. 19. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tools or these instructions to operate power tools. Power tools are dangerous in the hands of untrained users. 20. Maintain power tools. Check

Refer to the chart for recommended dial settings. MATERIAL SUGGESTED DIAL SETTINGS* Mild Steel 2-3 Wood 5 Nail-Embedded Wood 5 Stainless Steel 1-3 Drywall 4-5 Fiberglass 1-3 Plastics 1-3 Cast Iron 2-3 Non-Ferrous 2-3 Metals * These are only suggested settings; the actual optimum setting may vary depending on line voltage, blade selected and user preference. Trigger Speed Control Switch Super Sawzalls® are equipped with a trigger speed control switch. It may be operated at any speed from zero str

WARNING To reduce the risk of injury, keep hands away from the blade and other moving parts. the desired position. Trigger Speed Control Switch • If the broken stub doesn't extend far 4. To lock the shoe in position, push in the The Sawzall ® HatchetTM is equipped with a enough to be grabbed by its corner, use shoe release lever. a thin blade with small teeth (such as a trigger speed control switch. It may be opmetal cutting blade) to hook the blade 5. After adjusting the shoe, slowly pull erate

PART NO. DESCRIPTION OF PART NO. REQ. 1 02-04-0719 Ball Bearing (1) 2 02-04-5130 Ball Bearing (1) 3 02-50-2150 Needle Bearing (1) 4 05-88-0302 K50 x 60mm Washer Hd. PT Screw (2) 5 05-88-8309 K50 x 35mm Washer Hd. PT Screw (1) 7 06-82-5363 8-32 x 1 Washer Hd. Taptite T-20 Screw (2) 8 06-82-7253 8-32 x .38 Taptite T-20 Screw (3) 9 06-82-7261 6-19 x .687 Slotted Plastite T-15 Screw (4) 10 06-82-7276 6-19 x 1.00 Slotted Plastite T-15 Screw (2) 13 12-20-0719 Service Nameplate Kit (1) 14 28-14-0997 Ge

Handle 2. Trigger 3. Trigger lock switch 4. Nameplate 1 2 34 56 7 8 9 5. Insulating boot 6. Quik-Lok™ blade clamp 7. Blade 8. Adjustable pivot shoe 9. Shoe release lever 4 TOOL ASSEMBLY WARNING Always lock trigger or remove battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous. WARNING Recharge only with the charger specified for the battery pack. For specific charging instructions, read the operator's manual su