Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: DeWalt Dateigröße: 19.76 mb Dateiname: 1ec6fe54-8317-4ccb-b5ea-fba81c254a0f.pdf Unterrichtssprache:

REVIEW SAFETY RULES AND OPERATING INSTRUCTIONS FREQUENTLY. This booklet is provided for your convenience: iw the use ami care of your new DeWalt Saw. These instructions include operation, usage, precautions^ preventive maintenance, maintenance and other pertinent data to assist you in assuring long; life and dependable service from your saw. 700 8" RADIAL ARM SAW No. 7700/3400,120 VOLT, TYPE 5 No. 7700-01,220 VOLT, TYPE 5 Bulletin No. 8814 - INDEX Unpacking, Set-Up..............2-4 MacfiineControls................. 5 Introduction.....................6 Rules for Operation • ini Maintenance.............. 7*8 Alignments................... 9*13 Alignment Guide................ 14 PrecuttingWork Surface.......15-17 Sasic Cuts .................. 11-21 Saw Slades & Accessories.........22 fancf Cuts.................. 23-24 Farts Lists, Order Instruc....... 25*28 8&D Service Centers ............ 32 UNPACKING & SET-UP INSTRUCTIONS You can easily set up your new DeWALT Radial Arm Saw, one of America’s most popular power tools. Handling is minimized because every machine is partially assembled for shipment to you. The only tools required are the wrenches furnished with the machine, Phillips screwdriver, regular screwdriver, adjustable wrench, a good square, and a small amount of grease or petroleum jelly. Just follow this easy step-by-step procedure on pages 3 & 4 in setting up your new saw! TTTT 2 ooo o 3000« 4 24 © »2 o 26# 11 15 i'X THIS IS THE PARTS ILLUSTRATION MENTIONED IN STEF 3 ON FACING PAGE PARTS IDENTIFICATION NO, ITEM QUANTITY NO. ITEM QUANTITY N0. ITEM 1 3/8" Dia. Flat Hd. Screws 4 10 3/8" 1.0. Washer 1 19 Washer 2 Lock Washers 4 ' 11 Base Clamp 1 20 Hex Nut 3 3/8" Oia. Nuts 4 - 12 Square Nut 1 21 Anti-Kickback Device 4 Large flange Hex Nuts 1 13 1-3/4* Ig. Hex Bolt 1 22 Wing Bolt 5 Self Tapping Screws 4 14 Square Nut 1 23 Key i Thumb Screws 2 15 Inserts 2 24 * Arbor Washer 7 Cleat Brackets 2 li Handles 2 21 Spacer Wash*« 8 Eyelets n 1/4-20 x 1/2" Lg. Carriage Bolt 1 21 Arbor Screw* 9 Large Base Washer 1 ' 11 Guard Extension 1 2? 128Wrenches 4 Assembled to Saw QUANTITY 2 1 Kmmm arm m4 motor assembly from carton. Lay out contents of hardware bags in sequence illustrated in the photograph on page two (2), handy to the assembly area (item 26 is assembled to saw arbor). Familiarize yourself with base and table assembly on page 27 before assembling saw. i Remove remainder of contents from carton. 3. 4m AsstmlM tatote trim« (2 large channel pieces) to Mi* to» using (4) flat Heart .3/8* dia. screws, lock ■ m^ms and 3/8* dm nuts. Tighten securely with wrench. See page 27. 5. Attach the cleats to the underside of the table with the self-tapping screws. Note: Holes are already drilled for you. Tight»» securely but do not strip the table top. 6. Screw <4) large flange hex nuts onto the threaded studs of the table cleats so the studs extend beyond the nuts approximately 1*5/16*. . Install the table to the frame by putting cleat studs thru the elongated holes is the frame 8. Screw (4) large flange hex nuts to the cleat studs and leave loose. These will be tightened when you adjust the table 90° to the arm. > Place the fence and back board in position. 10. Screw the long thumb screw into the cleat bracket and install bracket by slipping it through the rectangular hole in the cleat With one hand hold the eyelet against the back board in line with the thumb screw while turning the thumb screw with the other hand to force the stud into the eyelet until it snaps in place. Repeat for the other side. 3 11 • Hold the large base wash®* at an angle and insert it into the base from the bottom as shown. IMPORTANT—the bottom of the arm should rest on this thrust washer—see step 13. 14® Place insert into plastic knob. Push knob onto clamp handle. * LéL Remove the arm and motor assembly from the packing. Lubricate about 5* of arm under miter scale by applying grease over entire surface. Insert the rear of the arm into the base as shown. Turn and “wiggle'* the end of the arm to ease it in place. Pull the miter locator pin so the arm goes all the way down to the base washer. 15. Put the guard extension in place. Install the 1/4-20 x 1/2* carriage bolt into the rear square hole of the saw guard with the bolt head inside. Secure it with a washer and hex nut using the wrench provided. 1/. Do not plug saw into receptacle at this time. Insert key in slot with notch down. Switch can now be operated. Turn switch off and remove key with upward and outward motion. 18. MOUNT YOUR SAW ON A LEG STAND, STURDY WORK BENCH. OR APPROPRIATE TABLE. TABLE TOP OF SAW SHOULD PROTRUDE APPROXIMATELY FOUR (4) INCHES OVER MOUNTING SURFACE. THIS UNIT WILL FIT A 35021 DELUXE MACHINE STAND. 19. REFER NEXT TO MACHINE CONTROLS, INTRODUCTION AND ALIGNMENT PROCEDURES ON FOLLOWING PAGES. YOUR SAW MUST BE COMPLETELY ALIGNED BEFORE MAKING ANY CUTS. INSTALLING BLADE To install the blade rotate the saw to...

Herunterladen

Geben Sie zwei Ziffern: