Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: DeWalt Dateigröße: 1.67 mb Dateiname: Unterrichtssprache:

The following information describes the safe and proper method for performing the most common sawing operations. This instruction manual does not provide information regarding the installation of a fence system. A fence system must be installed before use of the saw. Please refer to the fence instruction manual regarding the proper installation, alignment, and operation of the fence system. The use of attachments and accessories not recommended be Delta may result in injury. Never operate the saw without the proper table insert for the saw blade or cutter installed. QUICK OPERATIONS CHECKLIST Before using the saw each and every time, verify the following: 1. Blade is tight. 2. Bevel angle and height lock knobs are tight. 3. If ripping, ensure fence lock lever is tight and fence is parallel to the blade. 4. If crosscutting, miter gauge knob is tight. 5. Proper eye, hearing and respiratory equipment is being used. 6. The blade guard is properly attached and the anti-kickback pawls are functioning. Failure to adhere to these common safety rules can greatly increase the likelihood of injury. 18 BLADE GUARD AND SPLITTER USE The blade guard assembly provided with Delta saws (Fig. 48) must be used for all through-sawing operations. The splitter prevents the kerf from closing and binding the blade, causing kickback. The anti-kickback pawls prevent the workpiece and cut-off piece from being thrown back at the operator. The plastic guard prevents dust and debris from being thrown at the operator. To use the guard properly: 1. Make sure the splitter is aligned with the blade as described in the section “BLADE GUARD AND SPLITTER ASSEMBLY AND ALIGNMENT.” 2. Replace or sharpen the anti-kickback pawls when they become dull. 3. Keep the guard clean for visibility and free motion. 4. Do not use solvent or lubricants on the guard as they may severely damage the plastic. 5. Use caution when feeding workpieces that may catch on the guard and cause a bind or force the guard into the blade (such as when cutting moulding). Fig. 48 CROSS-CUTTING Cross-cutting requires the use of the miter gauge to posi tion and guide the work. Before starting the cut, raise the blade so that it is about 1/8” (3.2mm) higher than the top of the workpiece. Place the work against the miter gauge and advance both the gauge and work toward the saw blade (Fig. 49 ). You can use the miter gauge in either table slot. Start the cut slowly and hold the work firmly against the miter gauge and the table. Keep both hands on the miter gauge and workpiece. Do not touch the cut-off piece. Feed the workpiece steadily through the blade until the workpiece is completely cut. Shift the workpiece slightly sideways away from the blade, then pull the workpiece and miter guage back to the starting position. Remove the workpiece, then use a push stick to push the cut-off piece past the blade and off the table before beginning the next cut. For added safety and convenience, you can fit the miter gauge with an auxiliary wood-facing (C) Fig. 50 that should be at least 1 inch higher than the maximum depth of cut, and should extend out 12" or more to one side or the other depending on which miter gauge slot is being used. This auxiliary wood-facing (C) can be fastened to the front of the miter gauge by using two wood screws through the holes provided in the miter gauge body and into the wood-facing. Fig. 49 Fig. 50 C When cross-cutting a number of pieces to the same length, clamp a block of wood (B) to the fence and use it as a cutoff gauge (Fig. 51). The block (B) must be at least 3/4" thick to prevent the cut-off piece from binding between the blade and the fence during removal from the saw table. Always position this block of wood in front of the saw blade. Once the cut-off length is determined, lock the fence and use the miter gauge to feed the work into the cut. When using the block (B) Fig. 51 as a cut-off gauge, it is very important that the rear end of the block be positioned so the workpiece is clear of the block before it enters the blade. B Fig. 51 Never use the fence as a cut-off gauge when cross-cutting. 19 MITERING Mitering (the operation shown in Fig. 52) is the same as crosscutting except that the miter gauge (C) is locked at an angle other than 0°. Hold the workpiece firmly against the miter gauge and feed the work slowly into the blade to prevent the workpiece from moving. Use caution when starting the cut to prevent binding of the guard against the workpiece. Miter angles greater than 45° may force the guard into the saw blade and damage the guard. Before starting the motor, test the operation by feeding the workpiece into the guard. If the guard contacts the blade, place the work piece under the guard, NOT TOUCHING THE BLADE, before starting the motor. Fig. 52 C Certain workpiece shapes, such as moulding, may not lift the guard properly. Feed the work slowly to start the cut. BEVEL CROSSCUTTING Bevel crosscutting (shown in Fig. 53) is the same as crosscuttin...

Herunterladen

Geben Sie zwei Ziffern: