Login:
Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Anleitung DeWalt, modell 36-L31X

Hersteller: DeWalt
Dateigröße: 1.67 mb
Dateiname:
Unterrichtssprache:enesfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


24 P C D Fig. 24 P C D Fig. 25 E 14. Hold the blade guard and lower the saw blade. Install the table insert (E) Fig. 25 in the open ing of the saw table. 15. Place a straight edge (B) across the table at both ends of the table insert (Fig. 26). Ensure that the table insert (A) is level with the table. If an adjustment is necessary, turn the adjusting screws (C) with the 1/8" hex wrench. MOTOR COVER NOTE: If your Unisaw uses an LVC Starter Box, attach the two bottom spring clips to the motor cover. 1. Align the hole in the motor cover clip with the hole in the motor cover. Place a 13/64" flat washer on a 10-32 x 1/2" screw (A) Fig. 27. Insert the screw through the hole in the motor cover clip and thread the screw (A) in the tapped hole in the motor cover. Repeat this process for the remaining motor cover clip. 2. Place the motor cover in the opening of the Unisaw (Fig. 28). Place the rear motor cover clips inside the motor opening. Push the front of the motor cover until all four motor cover clips are engaged. 3. Align the hole (B) Fig. 29 in the bottom of the motor cover with the hole in the side of the saw cabinet. Place a 1/4" flat washer on a 1/4-20 x 5/8" hex-head screw. Insert the screw through the hole in the motor cover. Thread the screw in the hole in the side of the motor cabinet. Tighten securely. NOTE: To detach the motor cover, remove the 1/4-20 x 5/8" hex-head screw (B) Fig. 29, and push the motor cover to one side. This will depress the clips and you can remove the cover. Fig. 26 C A B C Fig. 27 A Fig. 28 Fig. 29 B 13 Do not mount the dust chute adapter unless you use a dust collection system. The dust chute adapter without the system will restrict the gravity feed opening for sawdust removal. You can store the miter gauge and arbor wrenches in the slots in the motor cover (Fig. 32). MITER GAUGE AND WRENCH STORAGE You can store the miter gauge and arbor wrenches in the slots in the motor cover (Fig. 32). MITER GAUGE AND WRENCH STORAGE RIP FENCE HOLDER BRACKETS Attach the rip fence holder brackets (A) Fig. 30 to the four holes located in the right hand side of the saw cabinet. Use the supplied four #10 x 1/2" sheet metal screws. DUST CHUTE ADAPTER Fig. 30 A The Unisaw is supplied with a dust chute connector to provide a means of connecting a 4" diameter dust collector hose to the machine. Align the four holes in the dust chute adapter (A) Fig. 31 with the four holes in the back of the saw cabinet (B). Attach the dust chute adapter with four #10 x 1/2" sheet metal screws. Fig. 32Fig. 31 A B OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS Make sure that the switch is in the “OFF” position before plugging cord into the outlet. Do not touch the Fig. 33 Fig. 34 A B C plug’s metal prongs when unplugging or plugging in the cord. STARTING AND STOPPING THE SAW To start the machine, push the “ON” button (A) Fig. 33. To stop the machine, push the “OFF” button (B). LOCKING THE SWITCH IN THE “OFF” POSITION IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use, using a padlock (C) Fig. 34 with a 3/16" diameter shackle (D). 14 In the event of a power outage (breaker or fuse trip), always move the switch to the “OFF” position until the main power is restored. OVERLOAD PROTECTION Your saw is supplied with overload protection. If the motor shuts off or fails to start due to overloading (cutting stock too fast, using a dull blade, using the saw beyond its capacity, etc.) or low voltage, let the motor cool three to five minutes. The overload will automatically reset itself and the machine can then be started again by pressing the “ON” button. If the motor continually shuts off due to overloading, contact a qualified electrician. RAISING AND LOWERING THE BLADE Raise or lower the blade with the front handwheel (A) Fig. 34. With the exception of hollow ground blades, raise the blade 1/8" to 1/4" above the top surface of the workpiece. With hollow-ground blades, raise the blade to the maximum height to provide greater clearance. To raise the saw blade, loosen lock knob (B) Fig. 34, and turn the handwheel (A), clockwise. To lower the saw blade, turn handwheel (A) counter-clockwise. Lock the sawblade by turning the lock knob (B) Fig. 34 clockwise. Only a small amount of force is required to lock the blade raising mechanism securely. Any added force merely puts unnecessary strain on the locking device. Limiting stops for raising or lowering are permanently built into the mechanism and need no further adjustment. Lock the blade in position before starting the saw. TILTING THE BLADE The blade tilting mechanism allows the blade to be tilted up to 45° to the right. To tilt the saw blade, loosen the lock knob (D) Fig. 34 and turn handwheel (C). A pointer indicates the angle of tilt on scale (E), marked in one-degree increments. To lock the saw blade, tighten the lock knob (D). Lock the blade in position before starting the saw. ADJUSTING 90° AND 45° POSITIVE ST...

Dieses Handbuch ist für folgende Modelle:
Kreissägen - 36-L51L (1.67 mb)
Kreissägen - 36-L51 (1.67 mb)
Kreissägen - 36-L53L (1.67 mb)
Kreissägen - 36-L51X (1.67 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien