Login:
Sortierung : Dateiname ↑   heruntergeladen   Bewertung   Dateigröße ↑  
heruntergeladen wurde: 15   Dateigröße: 371 kb   Hersteller: DeWalt  
Kategorie: Kreissägen
@name

DW788/383329 8/6/02 10:35 AM Page 3 English IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING SAW • DO NOT WEAR GLOVES, NECKTIES, JEWELRY OR LOOSE CLOTHING • CONTAIN LONG HAIR • ALWAYS WEAR EYE PROTECTION • INSTALL BLADE WITH TEETH POINTING DOWNWARD TOWARD THE TABLE BEFORE OPERATING SAW • MAINTAIN PROPER ADJUSTMENT OF BLADE TENSION BLADE GUARD BEFORE OPE

heruntergeladen wurde: 1   Dateigröße: 2 mb   Hersteller: DeWalt  
Kategorie: Kreissägen
@name@name@name

5. Slide the two legs into the holes in the saw shoe as shown in Figure 4. INSTALL RIP GUIDE IN THIS DIRECTION FIG. 4 D C C 6. Adjust the front and rear scales to read the same measurement. WARNING: Both front and rear scales MUST BE set at the same rip width or serious personal injury due to kickback may occur. 7. Securely tighten front (C) and (D) rear locking screws at desired rip width. DW5100 DUAL PORT RIP GUIDE Safety Warnings WARNING: For your own safety, read the saw instruction manual b

heruntergeladen wurde: 1   Dateigröße: 2 mb   Hersteller: DeWalt  
Kategorie: Kreissägen
@name@name@name

• Properly clamp material to avoid movement and vibration. MAINTENANCE Motor Brush Inspection andReplacement (Fig. 10) WARNING: Turn off and unplug the tool. Be sure the trigger switch is in the OFF position. Brushes should be regularly inspected for wear. To inspect brush- .3" (8mm) Y W X Y .3" (8mm) Y W X Y centers or other qualified service organizations, FIG. 10 Z tical replacement parts. NOTE: Unit may be converted to a 3-wire twist lock authorized service center. Lubrication Closed-type, g

heruntergeladen wurde: 3   Dateigröße: 0 kb   Hersteller: DeWalt  
Kategorie: Kreissägen

heruntergeladen wurde: 1   Dateigröße: 4 mb   Hersteller: DeWalt  
Kategorie: Kreissägen
@name@name@name

4. The third hole is at the rear of the machine. An alternate method of securing the scroll saw to a supporting surface is to fasten the scroll saw to a mounting board. Then securely clamp the mounting board to a stand or workbench using two or more C-clamps. NOTE: For proper stability, the holes in the mounting board must be countersunk at the bottom so that the fastener heads are flush with the bottom surface of the mounting board. Fig. 4 A OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS STARTI

heruntergeladen wurde: 5   Dateigröße: 2 mb   Hersteller: DeWalt  
Kategorie: Kreissägen
@name@name@name

386782-01 DW705 Copyright 2001, 2002 Before returning call 1-800-4-DEWALT IF YOU SHOULD PURCHASE, CALL 1-800- IN MOST CASES, REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER IF YOU HAVE A SUGGESTION OR GIVE US A CALL. YOUR FEEDBACK IS VITAL TO THE SUCCESS OF DEWALT'S QUALITY IMPROVEMENT INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO INSTRUCTION MANUAL ANTES DE USAR EL PRODUCTO. GUIDE D.UTILISATION MANUAL DE INSTRUCCIONES DW705 (120 Volt)/DW705 (220 Vol

heruntergeladen wurde: 4   Dateigröße: 20 mb   Hersteller: DeWalt  
Kategorie: Kreissägen
@name

Turn the motor “OFF”. Figure K5C Moving the saw back through lb« trough and 1/4-circle kerfs, bring the saw again to the position at the-end of the arm as shown in Figure K5. Tighten Rip Lock and release Yoke Clamp Handle. Turn -motor “ON" and temporarily press the Yoke Locator Pin Handle as you start to rotate the yoke counterclockwise (Figure K5D). Continue rotating until the Locator. Pin stops the yoke, after a 1/4-circie cut, with the blade parallel to the fence. Now, with the motor still

heruntergeladen wurde: 6   Dateigröße: 0 kb   Hersteller: DeWalt  
Kategorie: Kreissägen

heruntergeladen wurde: 4   Dateigröße: 2 mb   Hersteller: DeWalt  
Kategorie: Kreissägen
@name@name@name

For most work, 3/4” stock is suitable, although an occasional job may require 1” facing. Fig. 64 A 23 CONSTRUCTING A FEATHERBOARD Featherboards are used to keep the work in contact with the fence and table (Fig. 69), and help prevent kickbacks. Dimensions for making a typical featherboard are shown in Fig. 69. Make your featherboard from a straight piece of wood that is free of knots and cracks. Clamp the featherboard to the fence and table so that the leading edge of the featherboard will suppo

heruntergeladen wurde: 5   Dateigröße: 2 mb   Hersteller: DeWalt  
Kategorie: Kreissägen
@name@name@name

Fig. 49 Fig. 50 C When cross-cutting a number of pieces to the same length, clamp a block of wood (B) to the fence and use it as a cutoff gauge (Fig. 51). The block (B) must be at least 3/4" thick to prevent the cut-off piece from binding between the blade and the fence during removal from the saw table. Always position this block of wood in front of the saw blade. Once the cut-off length is determined, lock the fence and use the miter gauge to feed the work into the cut. When using the block (B





Kategorien