Do not operate the unit if gasoline is spilled. Wipe the unit clean and move it away from the spill. Avoid creating any ignition until the gasoline has evaporated. Do not store the unit near an open flame or any equipment such as a stove, furnace, water heater, etc. which utilizes a pilot light or sparking device. A spark arrester must be added to the muffler of this engine if it is to be used on any forest covered, brush covered or grass covered unimproved land. The arrester must be maintained

It is recommended to: . Use electrical devices with prong power cords. . Use an extension cord with a hole receptacle and a prong plug at the opposite ends to ensure continuity of the ground protection from the unit to appliance. John Deere strongly recommend that all applicable federal, state and local regulations relating to grounding specifications be checked and followed. LINE TRANSFER SWITCH: If this unit is used for standby service, it must have a transfer switch between the utility power

Turn off the unit. . Disconnect spark plug wire from engine. . Open all drains. 4. Wait for the unit to cool before starting service. Maintenance Chart: To ensure satisfactory operation over an extended period of time, an engine requires normal maintenance at regular intervals. The Periodic Maintenance Chart below shows periodic inspection and maintenance items and suitable intervals. The bullet mark designates that the corresponding item should be performed at that interval. NOTE: Some adjustme

READ THIS MANUAL carefully to learn how to operate and service your machine correctly. Failure to do so could result in personal injury or equipment damage. This manual and safety signs on your machine may also be available in other languages. (See your John Deere dealer to order.) THIS MANUAL SHOULD BE CONSIDERED a permanent part of your machine and should remain with the machine when you sell it. MEASUREMENTS in this manual are given in both metric and customary U.S. unit equivalents. Use only

THEY MAY IGNITE. ALWAYS OPERATE THE COMPRESSOR IN A WELL VENTILATED I AWAY FROM SPRAY AREA. AN ADDITIONAL LENGTH OF HOSE MAY BE REQUIRED. SECURE LOCATION AWAY FROM COMPRESSOR. NEVER PLACE OBJECTS AGAINST OR ON TOP OF COMPRESSOR. OPERATE IN AN OPEN AREA AT LEAST ANY WALL OR OBSTRUCTION THAT WOULD RESTRICT THE FLOW OF FRESH AIR TO THE VENTILATION OPENINGS. RISK OF ELECTRIC SHOCK YOUR AIR COMPRESSOR IS POWERED BY ELECTRICITY. LIKE ANY OTHER ELECTRICALLY POWERED DEVICE, IF IT IS NOT NEVER O

plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. _ Type___ Serial No._ Part No. 888970-799 IMPORTANT SAFETY INSTRUCTIONS When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongl

Your tool is wired at the factory for operation using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15amp branch circuit. Use a 15amp time delay type fuse or circuit breaker. To reduce the risk of shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately. The A-C motor used on this compressor is a PSC, permanent split capacitor type, having the following specification. It is wired at the factory for operation on 110V-120

The incoming wires and the compressor electrical connections should be checked. Loose connections will cause malfunctions. Unit does not make any or very little air Drain valve open Air leak Restricted or blocked intake Make sure the drain valve at the bottom of the tank is closed. Check the entire system for leaks, including the compressor unit and any piping attached to the compressor Make sure that the air intake of the compressor is not blocked in any way. Continued on next page 15 Operating

Refer to motor name plate for electrical ratings and specifications. 3. The line wire is the proper size and that no other equipment is operated from the same line. The chart gives minimum recommended wire sizes for compressor installations. MiniMuM pipe Size for CoMpreSSed Air line CfM length of piping System 25 feet 50 feet 100 feet 250 feet 10 20 40 60 100 1/2 inch 3/4 inch 3/4 inch 3/4 inch 1 inch 1/2 inch 3/4 inch 1 inch 1 inch 1 inch 3/4 inch 3/4 inch 1 inch 1 inch 1 inch 3/4 inch 1 inch 1

. . . . . . . . . . . . . . . . . . . . . . . .1 Safety Guidelines . . . . . . . . . . . . . . . . . . . . . .2 Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . .2 Important Safety Information . . . . . . . . . .2 Getting To Know Your Compressor . . . . .4 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Maintenance. . . . . . . . . . .