FRONT PANEL EDGE LOCKED UNLOCKED 6 INSTALLATION (cont.) Plugging in the Unit • Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are present, wipe off with a clean, dry cloth. • Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair. • For the Classic Plus 26 model, fully insert plug into the A/C outlet and rotate clockwise until it locks in place. WARNING: • If the po

If dust and/or dirt are present, wipe off with a clean, dry cloth. . Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair. . Clean the air filters. . Empty all water from the drain tank. 16 TROUBLESHOOTING Self-Diagnostic Codes Self-Diagnostic Codes will be displayed on the Control Board under the following conditions: Code Condition dF When the evaporator thermistor disengages the compressor. FL When t

• When the water collects to level (A) in the pump reservoir, the drain pump begins to operate and discharges the water. • When the water level drops below level (B), the drain A B pump will stop. NOTE: • If for any reason the water level exceeds that of level (A) in the pump reservoir, an overflow Drain Switch will stop the compressor operation. • If the Fan Mode Control DIP Switch (see pg.13) has been set from the COOL to the STOP position, the Fan will also turn off while the drain pump is di

RETAINER FILTER 17CLIP CLIPVELCRO® ATTACHMENT POINTS FILTER DAILY INSPECTION & MAINTENANCE (cont.) Filter Cleaning Method . Remove dust from the element with a vacuum cleaner, or rinse in cold or lukewarm water. If the element is extremely dirty, wash with a neutral detergent. . After the element has been cleaned, rinse with clean running water, allow to dry, then FILTER reinstall. In-Season/Off-Season Inspection & Maintenance ¦ In-Season . Check the prongs and surface of the power cord plug for

(SET POINT temperature equals inlet air or room temperature.) The unit has been preset at the factory for continuous fan operation. • Temperature Scale Display DIP Switch The Temperature Scale Display DIP Switch changes the temperature(s) that are displayed to either °C or °F. The unit has been preset from the factory to display the temperature(s) in °F. NOTE: If you wish to change the fan mode operation (COOLOPERATE to COOLSTOP), and/or the Temperature Scale Display (°F to °C), contact your Mov

. AM/PM LED Illuminates to indicate AM or PM time of day. . Program RUN Activates/deactivates a program. Button . Program SET Allows the user to program the unit or Button check the current program. START TIME LED Illuminates to indicate the current step END TIME LED that is being programmed into the unit. SET CLOCK LED CLOCK/TIMER Allows the user to set the clock and program Buttons the start and end time of operation. 9 OPERATION (cont.) Operating in COOL Mode . The unit can be operated in COO

All rights reserved. This book may not be reproduced or copied, in whole or in part, without the written permission of the publisher. DENSO SALES CALIFORNIA, INC. reserves the right to make changes without prior notice. MovinCool is a registerd trademark of DENSO Corporation. OPERATION MANUAL OFFICE PRO 18 ii Table of Contents FOREWORD ..................................................................................... 1 Definition of Terms ......................................................

• The Office Pro 36 is equipped with a six (6) foot (1.8 meter) AFCI power cord. If replacement, fixed location (hard wired) or power cord lengthening (extension cord) cords are required, contact your reseller or a qualified licensed electrician for approved replacement methods. • Never fold, or place heavy objects on the power cord. This could result in damage to the power cord causing electrical shock or fire. • Do not place water or any other liquid on the unit. This can cause damage to the u

FL When the drain tank switch shuts off the unit (FULL T TTANK ANKANKANK LED flashes). AS When unit disengages the compressor while the condensate pump is discharging water. HP When the high pressure switch disengages the compressor. LO Lowest temperature set point. FILTER Note: If AS does not disappear from display, contact your distributor. 9 Check the following points before calling a qualified technician. SYMPTOM SYMPTOMSYMPTOMSYMPTOM POSSIBLE CAUSE POSSIBLE CAUSEPOSSIBLE CAUSEPOSSIBLE CAUSE

A55537 © 1999 DENSO SALES CALIFORNIA, INC. All rights reserved. This book may not be reproduced or copied, in whole or in part, without the written permission of the publisher. DENSO SALES CALIFORNIA, INC. reserves the right to make changes without prior notice. MovinCool is a registerd trademark of DENSO Sales California, Inc. SERVICE MANUAL CLASSIC PLUS 26 FOREWORD This manual has been published to service the MovinCool Classic Plus 26. Please use this service manual only when servicing the Cl