2009 - REV. 0 Printed in U.S.A. DistributedBy: Ordering Information “The Stinger has earned the trusted ARI Performance Certified™ seal, an assurance of the product’s performance in accordance with ARI Standard 740.” The new Stinger™ comes equipped with the new vacuum shut off allowing for unattended recovery operation, an easy-to-read low vacuum/tank full LED, carrying strap, and improved packaging to protect knobs and gauges. Providing you with new safety and reliability, the upgraded Stinger™

When operating this equipment, use good judgment work. and safety precautions to avoid damage to equipment and AVOID SPILLING liquid refrigerant on skin or getting it into the eyes. property or injury to personnel. USE SAFETY GOGGLES. Wash any spills from the skin with soap and Be sure you understand and follow the procedures and water. If liquid refrigerant enters the eyes, IMMEDIATELY FLUSH EYESsafety precautions contained in the chiller instructions as with water and consult a physician. well

10). C. Check to make sure that the cabinet is slanted slightly downward on the outside. If necessary, re-adjust support bracket as shown in (Fig. 7). Fig. 10 1/4" Screws Fig. 11 7. Secure Shutters A. Carefully slide the air conditioner back into the cabinet.(Please seek assistance for this procedure). B. Reinstall the slide-out-chassis security screws (removed earlier) on both sides of the cabinet. See (Fig. 12). Secure the top of the frames to the window sash with (2) 3/4" screws. C. Now, secu

See (Fig. 8). Fig. 5 Bracket Assembly Bracket Bolts Leveling Screw V-slot 90 Angle Support Brackets (TOP VIEW) Center Window sill V-slot (2) 3/4" screws per bracket Bracket Assembly Leveling Screw Outer Wall Construction 3/16" Maximum B. Measure the inside window sill width and find the center as shown in (Fig. 6). Align the V-slot in each bracket on these marks and mount the brackets to the sill using 3/4" screws provided. Brackets should be perpendicular to the inside window sill. See (Fig. 6)

To avoid installation difficulties, read instructions completely before starting. This manual contains information for the installation and operation of your room air conditioner. Note: The figures in this manual are based on the external view of a standard model. Consequently, the shape may differ from that of the air conditioner you have selected. Part Identification Introduction Mechanical control model Cabinet Exterior Air Inlet Air Outlet Fresh Air Vent Lever Control Knob Power Cord Front P

Please seek assistance for this procedure. Fig. 2 Fig. 1 Right side Philips screws Shutter Frame Right Shutter 1/4" screw For 10K to 12K models Channel 1/4" Screw Fig. 3 Fig. 4 Installation instructions 3. Assembly of the upper & lower channels to the cabinet A. " L" Shaped Top Channel: Stick the double adhering seal to the " L" shaped top channel, and then Install the "L" shaped top channel to the cabinet as shown in (Fig. 3) using (5) 1/4" screws. B. "n" Shaped Bottom Channel installed as show

Insert new batteries making sure that the (+) and (-) of battery are matched correctly. Reattach the cover by sliding it back into position. Note: Use 2 LR06 AA(1.5volt) batteries. Do not use rechargeable batteries. Replace batteries with new ones of the same type when the display becomes dim. To operate the room air conditioner, aim the remote control to the signal receptor. The remote control will operate the air conditioner at a distance of up to 23 feet when pointing at signal receptor of un

3. Use drapes, curtains, or shades to keep direct sunlight from heating your room, but DO NOT obstruct the air conditioner. Allow air to circulate around the unit without obstructions. 4. Start your air conditioner before outdoor air becomes hot/cold and uncomfortable. This avoids an initial period of discomfort while the unit is cooling or heating off the room. 5. When outdoor temperature is cool enough, use HIGH or LOW FAN only. This circulates indoor air, providing some cooling comfort, and u

LOW COOL provides cooling, automatically with minimum air circulation. Recommended for nighttime use. MED COOL provides cooling, automatically with middle air circulation. Recommended for nighttime use. HIGH COOL provides cooling, automatically with quick cooling or for extremely hot days. Once room is cooled, reduce setting to LOW COOL. NOTE: After setting the mode, allow 3 minutes before switching to another mode. OFF will completely shut-off the unit. THERMOSTAT The thermostat automatically c

ALL WARRANTIES, EXPRESSED OR IMPLIED, LAST FOR 5 YEARS FROM THE DATE OF ORIGINAL PURCHASE. THIS WARRANTY DOES NOT COVER LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY CAUSE WHATSOEVER. This warranty is extended to the original owner and any succeeding owner for products purchased for home use within the USA. Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific rights, and you may also have other rights which may