Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
FRONT PANEL EDGE LOCKED UNLOCKED 6 INSTALLATION (cont.) Plugging in the Unit • Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are present, wipe off with a clean, dry cloth. • Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair. • For the Classic Plus 26 model, fully insert plug into the A/C outlet and rotate clockwise until it locks in place. WARNING: • If the power cord or plug is damaged, repair should only be performed by qualified electrical personnel. • Do not connect/disconnect the power cord or attempt to operate buttons with wet hands. This could result in electrical shock. CAUTION: • Classic Plus 14 model ONLY: The AC outlet (115 VAC Single Phase, 60Hz) needs to be rated at 15A or higher. Do not share the outlet with any other instrument or equipment. • Classic Plus 26 model ONLY: The AC outlet (208/230 VAC Single Phase, 60Hz) needs to be rated at 20A or higher. Do not share outlet with any other instrument or equipment. NOTE: • Make sure the AC outlet is free of dirt, dust, oil, water, or any other foreign matter. • The Classic Plus 14 model is equipped with an approved NEMA plug configuration (L5-15). the appropriate outlet must be used for this plug type. • The Classic Plus 26 model is equipped with an approved NEMA plug configuration (L6-20). The appropriate outlet must be used for this plug type. 7 FEATURES Both models feature: • An electronic control panel which allows the user to control the unit’s operation easily. • Dual fan speeds (either High or Low) in both COOL and Fan Only modes. • A digital display that indicates the temperature SET POINT (either Fahrenheit or Celsius) in which the COOL Mode will operate. This is also the local temperature the unit will try to maintain. The Temperature Set Point can be adjusted by the SET TEMP buttons (Ў/^). • A condensate drain TANK FULL indicator display (LED). • An automatic restart feature when the power is lost and regained. The unit will return to the operating mode and temperature SET POINT it was in prior to the loss of power. 8 OPERATION Control Panel Before operating the unit, it is important to familiarize yourself with the basic controls located on the control panel. SET TEMP FAN ON/OFF COOL ON/OFF Classic Plus Activates/deactivates the COOL mode/ turns the unit off. Activates/deactivates the HIGH or LOW fan mode. Increases/decreases the temperature set point. Flashes when the drain tank is full. Indicates the current temperature set point. Illuminates to indicate the current temperature being displayed is either in °C or °F. . COOL ON/OFF Button . FAN ON/OFF Buttons . SET TEMP Buttons (Ў/^) . TANK FULL LED . SET POINT Display . Temperature Scale LED 9 OPERATION (cont.) Operating in COOL Mode The unit can be operated in COOL mode by pressing the COOL ON/OFF button (LED illuminates). NOTE: In COOL mode the unit can only be turned off by pressing the COOL ON/OFF button again, not by pressing the fan buttons. . Change the fan speed by pressing the HIGH or LOW fan buttons. . Change the temperature set point by pressing the SET TEMP buttons (Ў/^). NOTE: When turning the unit on, the temperature set point and fan speed are determined by the last operating mode. Operating in Fan Only Mode . The unit can also be operated in Fan Only mode by pressing either the HIGH or LOW fan buttons (LED illuminates). . The unit can then be turned off by pressing the fan speed button that is illuminated. Changing from Fan Only Mode to COOL Mode The COOL mode can be activated while the unit is operating in Fan Only mode. To do this, simply press the COOL ON/OFF button (LED illuminates). NOTE: The Fan Only mode will not operate after the COOL mode has been activated. After the COOL mode has been activated, the unit cannot be turned off by pressing the fan buttons. The COOL ON/OFF button must be pressed. 10 OPERATION (cont.) Operating Modes Both Classic Plus models operate in 2 modes, FAN Only and COOL. When in FAN Only mode the unit circulates the surrounding air. When in COOL mode, the compressor is engaged and cool air is circulated. ¦ COOL Mode Both models will operate in FAN Only mode for approximately 120 seconds before the compressor engages (compressor time delay program is 120 + 10 seconds). ¦ Temperature Control The room temperature thermistor allows the unit to switch automatically between COOL and FAN Only modes. This is dependent upon inlet air temperature versus SET POINT temperature. ¦ Fan Mode Control DIP Switch The Fan Mode Control DIP Switch determines whether the FAN will continue to operate or stop when the compressor cycles off. (SET POINT temperature equals inlet air or room temperature.) The unit has been preset at the factory for continuous fan operation. ¦ Temperature Scale Display DIP Switch The Temperature Scale Display DIP Switch changes the SET POINT temperature that is displayed to either °C or °F. The ...
Dieses Handbuch ist für folgende Modelle:Splitgeräte - CLASSIC PLUS 26 (2.54 mb)