Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Replace Covers and Cables
101.Replaceallcoversasdescribedinpanel6:
CAUTION
Replace all covers before operating the NetServer,
"Removing and Replacing the Covers."
even for a short time. Otherwise, damage to system
components may result due to improper cooling air
2. Connect the AC power cord and all other
flow.
cables.
Verify Installed Accessories (Optional)
11 Ifyouwish,youmaynowverifyaccessoriesyouhave
installed. Turn on power to the HP NetServer and the
NOTE
SCSI devices connected to a disk array controller
monitor, and observe the boot screen.
board (DAC), or the integrated NetRAID controller
cannot be displayed at boot time, nor can an ISA
The boot screen lists the hardware, as it is detected,
non-Plug-and-Play board be displayed at boot
such as CPU, memory, and accessory boards. If the
time.
system fails to boot, follow the instructions on the
screen.
Configure the HP NetServer
121. TurnontheHPNetServerandmonitor,insertthe
Assistant.
HP Navigator CD-ROM into the drive, and press the
Reset button. If the system fails to boot, follow the
7.
Show System Information: Select "View System Information" to
instructions on the screen.
get information about accessory boards and devices. Select "View
Resources" to view used and available system resources.
8.
Configure Mass Storage. This NetServer is shipped with the hot-
NOTE
If you have installed an ISA non-Plug-and-Play
accessory board, you must reserve system
swap mass storage device(s) unconfigured. To configure the
resources for it by using the Setup Utility. Start the
drive(s), do one of the following:
Setup Utility by pressing function key [F2] when
! Run HP NetRAID Assistant to configure one or more RAID
prompted during the boot process.
logical drives. To run HP NetRAID Assistant, select "Execute"
from the Configure Disk Array screen.
When the Setup Utility starts, select "Configuration,"
! Exclude SCSI A Channel from the integrated HP NetRAID
and then select "ISA non-Plug-and-Play Devices."
controller, as follows:
Use the arrow keys to highlight a selection, press
ENTER to display its options, and use the +/- keys to
a.
!
Restart the HP NetServer.
change values. When you've finished, save the
b.
!
Press function key [F2] when prompted.
changes and exit the utility.
c.
!
When the SETUP utility menu is displayed, use the up and
down arrow keys to highlight the "Include SCSI A Channel
For more information about reserving system
[Yes]" selection.
resources, refer to Information Assistant and to
"Configuring an ISA Non-Plug-and-Play Board" in the
d.
!
Use the + and - keys to change it to "Include SCSI A Channel
HP NetServer LH 4 / LH 4r User Guide.
[No]."
e.
!
Press function key [F10] to save the configuration and exit
(If the system hangs before the Setup Utility starts,
the utility program.
remove the ISA non-Plug-and Play board, run the
f.
!
Answer "Yes" to the question "Save Configuration and Exit
Setup utility to reserve system resources for it, then
Now?" The HP NetServer will reboot, and HP Navigator will
reinstall the board.)
restart.
9.
Install the NOS: If you selected the HP automated NOS
installation process, you will be guided through the process by a
2.
Run Configuration Assistant and Installation
series of HP display screens:
Assistant: If you want to change the language, select
! Install Utility Partition: This step creates a disk utility partition on
"Set Preferences" from the HP Navigator main menu
the server boot hard disk drive where HP Navigator will copy
and choose a language. Select "Configuration and
troubleshooting and other utilities. The utility partition is not
Installation Assistant." Select "Express" from the next
available under SCO® UNIX. Select "Execute" on the Install
screen to begin the "Express" mode of configuration.
Utility Partition screen to install the partition.
"Custom" configuration mode and "Replication"
! Execute Card Utilities: Select "Execute" on the Execute Card
configuration mode are also available. Refer to the HP
Utilities screen to run the accessory board configuration utilities.
NetServer LH 4/ LH 4r User Guide for details.
! Follow the instructions on the screen and in the network
3.
Choose a NOS: Select the NOS you will install, and the
operating system's installation instructions to perform the
version, if necessary. Installing the optional Novell®
manual NOS installation.
IntranetWare® NOS, which is part of the HP NetServer
! For Manual NOS Installation Only: Before you perform a
Software Option Package, requires a decryption key,
manual NOS installation, print out instructions and create NOS-
obtained in panel 5: "Preparation."
specific drivers diskette(s), as follows:
4.
Select the NOS installation mode: If you select certain
! A. Create Drivers Diskette(s): On the Create Drivers Diskette(s)
versions of Novell® NetWare® / IntranetWare® or
screen, select Create Drivers Diskette(s) to create one or
Microsoft® Windows™ NT Server, you will be asked,
more customized diskettes containing HP drivers and
"Would you like to use HP's automated mode of NOS
configuration files to use when you install the NOS.
installation?"
! B. Print and Read Instructions: On the Show NOS Installation
! Select "Yes" to choose automated NOS installation for
Instructions screen, select "Save to Disk" to copy the NOS
first-time installation of Novell NetWare / IntranetWare
installation instructions to disk. Then print them from disk.
or Microsoft Windows NT Server on a factory-
Read the instructions first, and then follow them to manually
configured HP NetServer.
install the NOS.
!
! Use the manual NOS installation if you are installing a
Install NOS:
NOS other than Novell NetWare / IntranetWare or
! A. Automated NOS Installation: For certain versions of Novell
Microsoft Windows NT Server, or if you have replaced
NetWare / IntranetWare or Microsoft Windows NT Server,
accessory components (for example, if you replaced
Configuration Assistant formats and partitions the hard disk
an HP network interface controller board with a third-
drive. Installation Assistant then guides you through the NOS
party board that is not on HP's Tested Products List,
installation and configures the NOS with the appropriate
use the manual NOS installation).
drivers for the HP-bundled configuration or for network
interface cards on HP's Tested Products List.
5.
View Configuration Advisories: Read the
Configuration Advisories and print them if necessary.
! B. Manual NOS Installation: Follow the instructions on the
Make any changes suggested in the advisories.
screen and the network operating system installation
instructions that you printed.
6.
Configure Remote Management: If you plan to
manage the HP NetServer LH 4 remotely, refer to the
10. Install HP TopTools: Refer to the HP NetServer Server
HP NetServer Remote Administrator Guide for
Management Reference Guide, and install HP TopTools.
instructions. Select "Configure Remote Management"
11. Refer to Information Assistant on the HP NetServer Online
on the Navigator screen to configure Integrated Remote
Documentation CD-ROM, for further information about your HP